background image

6/14 

Siemens 

Room Temperature Controllers 

N3057en 

Building Technologies 

 

2014-10-28 

External operating mode changeover D1-GND 

With the RDF110, a potential-free operating mode changeover switch (window switch, 
key card contact, etc.) can be connected to status input D1-GND. No additional power 
supply is required for detecting the position of the external switch. 

When the switch closes due to an open window, or unoccupied hotel room for instance, 
the operating mode will change to Economy (Energy saving). During this external 
operating mode changeover, neither the setpoint nor the control parameter nor fan 
mode can be changed. When pressing the setpoint or fan mode buttons, ECO will flash 
on the display, indicating that the operating mode is overridden from a remote location. 

The operating action of the switch (N.C. or N.O.) can be selected via parameter P19. 

Error handling 

When the room temperature is out of the measuring range, which means above 49 °C 
or below 0 °C, the display shows the limiting temperature in flashing figures, e.g. “0 °C” 
or “49 °C”.  
If the current setpoint is not OFF (see parameters 1 – 4), the controller is in heating 
mode and the temperature is below 0 °C, output Y11 will be energized. In all other 
cases, Y11 is deenergized. When the temperature returns to the measuring range, the 
controller will resume Normal operation. 
 
In case of an external sensor failure (short-circuit or open-circuit), the controller will 
immediately switch back to the internal sensor to ensure control. 
 
Should both the external and internal sensor fail, the display will flash “Err” to call the 
user‘s attention. 
 

Infrared remote control 

The RDF110/IR and RDF110.2/IR have an infrared receiver built in. Together with the 

IRA210 infrared remote control, the following operations can be performed from a 

remote location: 
 

  Selection of operating mode: Protection (Standby) / Normal operation  

  Adjustment of setpoint in Normal operation 

  Selection of fan mode: Automatic or manual fan speed 

 
Using parameter P25, infrared remote control can be disabled. 

Temperature out  

of range 

External sensor  

failure 

Summary of Contents for RDF110















Reviews: