background image

 

GAMMA 

instabus

 

Technical product information 

December 2009 

N 562/11 

Switching actuator, main module

 5WG1 

562-1AB11 

3x AC 230/400 V, 10 AX, C-load, load-check 

Siemens AG 

N 562/11, 6 pages 

Technical manual 

Industry Sector, Building Technologies 

Low Voltage Distribution 

© Siemens AG 2009 

Update: http://www.siemens.com/gamma 

P.O. Box 100953, D-93009 Regensburg 

Subject to change without further notice 

 

 

2.4.3.4/5 

General notes 

 

The operating instructions must be handed over to the 
client. 

 

A faulty device shall be sent with a Return Good Note 
for Service provided by the appropriate Siemens sales 
office to the following address: 
SIEMENS AG, Siemensstr. 10, D-93055 Regensburg 

 

If you have further questions concerning the product 
please contact our technical support: 

 

+49 (0) 180 50 50-222 
(0,14 €/min. from the German landline network, de-
viating mobile communications prices are possible) 

 

+49 (0) 180 50 50-223 
E-Mail: 

[email protected]

 

 www.siemens.com/automation/support-request 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for N 562/11







Reviews: