Siemens N 543D31 Manual Download Page 15

Page: 15 / 18

Smart Infrastructure

A6V11986596_en--_e

Building Products

2022-04-27

Type

N 545D31

N 543D51

Mechanical data

Fire load

5 MJ

9 MJ

Environmental conditions

Ambient temperature in operation

-5 °C...+45 °C (23 °F...113 °F)

Storage temperature

-20 °C...+70 °C (-4 °F...158 °F)

Transport temperature

-25 °C...+70 °C (-13 °F...158 °F)

Relative humidity
(non-condensing)

5 %...95 %

Climatic resistance

EN 50428

Protection settings

Degree of pollution (according to IEC
60664-1)

Overvoltage category
(according to IEC 60664-1)

III

Protection class (according to EN 60529)

IP20

Electrical safety, bus

yes

Electrical safety, device complies with

EN 50428

EMC requirements, device complies with

EN 50428

Test mark

KNX, EAC, RCM, WEEE, China-RoHS

CE mark

yes

Type

N 545D31

N 543D51

Reliability

Failure rate (at 40°C)

1776 fit

3816 fit

Summary of Contents for N 543D31



















Search results

Summary of Contents for N 543D31

Reviews:

Related manuals for N 543D31

Brands by name

Popular brands

Siemens N 543D31, Manual

Search results

Summary of Contents for N 543D31

Reviews:

Related manuals for N 543D31

Brands by name

Popular brands