Siemens Gigaset S430 User Manual Download Page 46

Page: 46 / 60

Appendix

Gigaset S430 / HGK-Taiwan-engl / A31008-M1625-Z201-1-7619 / appendix.fm / 18.01.2005

Appendix

Care

Wipe the base station and handset with

damp

cloth (do not use solvent) or an

antistatic cloth.

Never

use a dry cloth. This can cause

static.

Contact with liquid

If the handset has come into contact with

liquid:
1.

Switch the handset off and remove

the batteries immediately

2. Allow the liquid to drain from the hand-

set.

3. Pat all parts dry, then place the handset

with the battery compartment open

and the keypad facing down in a dry,

warm place

for at least 72 hours

(

not

in a microwave, oven etc.).

4. Do not activate the handset again

until it is dry.

When it has fully dried out you will nor-

mally be able to use it again.

Questions and answers

If you have any queries about the use of

your phone, you can contact us 24/7 at

www.siemens.com/gigasetcustomercare.

The table below contains a list of common

problems and possible solutions.

The display is blank.

1. The handset is not switched on.

Press and

hold

the end call key

2. The batteries are flat.

Charge or replace the batteries (page 7).

The handset does not respond to a key press.

The keypad lock is activated.

Press and

hold

the hash key

(page 8).

"Base station x"

flashes

in the display.

1. The handset is outside the range of the base

station.

Reduce the distance between handset/

base station.

2. The handset has been de-registered.

3. The base station is not switched on.

Check the base station mains adapter

(page 6).

Base Search flashes in the display.

The handset is set for

Best Base

and no base sta-

tion is switched on or within range.

Reduce the distance between handset/base

station.

Check the base station mains adapter

(page 6).

Handset does not ring.

1. The ringtone is switched off.

Activate the ringtone (page 35).

2. Call diversion set to

All Calls

Switch off Call Diversion (page 14).

You cannot hear a ringtone/dialling tone.

Base station's phone cord has been replaced.

When purchasing a new cord, ensure that it

has the correct pin connections (page 6).

Summary of Contents for Gigaset S430





























































Search results

Summary of Contents for Gigaset S430

Reviews:

Brands by name

Popular brands

Siemens Gigaset S430, User Manual

Search results

Summary of Contents for Gigaset S430

Reviews:

Brands by name

Popular brands