Siemens FLENDER GHDP Page 34 Assembly And Operating Instructions Manual Download

Page: 34 / 61

34 / 61

BA 5814 en 09/2014

Table 6:

Recommended lubricants for shrink disks after their cleaning

Lubricant

Form

Manufacturer

Molykote G Rapid

Spray or paste

DOW Corning

Aemasol MO 19 P

Spray or paste

A. C. Matthes

Unimoly P 5

Powder

Klüber Lubrication

gleitmo 100

Spray or paste

Fuchs Lubritec

Other lubricants may be used if they have the same characteristics.

•

Join the inner ring (3) and the outer ring (4).

•

Place the tensioning bolts and screw in some threads by your fingers.

Observe the manufacturer’s instructions for handling lubricants!

Fitting and startup must be carried out by properly trained specialist personnel.

6.3.2.4 Refitting the shrink disk

For refitting the shrink disk the procedure described in item 6.3.2.1 must be adhered to!

6.3.2.5 Inspection of the shrink disk

In all cases the inspection of the shrink disk should be carried out simultaneously with the
inspection of the gear unit,

however at least every 12 months

Inspection of the shrink disk is limited to a visual assessment of its condition. The following must be
observed when carrying out this work:

─

loose bolts

─

damage caused by force

─

flush position of the inner ring (3) in relation to the outer ring (4)

Summary of Contents for FLENDER GHDP






























































Search results

Summary of Contents for FLENDER GHDP

Reviews:

Related manuals for FLENDER GHDP

Brands by name

Popular brands

Siemens FLENDER GHDP, Assembly And Operating Instructions Manual

Search results

Summary of Contents for FLENDER GHDP

Reviews:

Related manuals for FLENDER GHDP

Brands by name

Popular brands