background image

3

Installation

Statutory requirements

This installation must conform with the following:

Manufacturer’s Installation instructions

Local Gas Fitting Regulations

Municipal Building Codes

Refer to AS/NZS 5601.1 for Gas Installations

S.A.A. Wiring Code

Local Electrical Regulations

Any other statutory regulations

Preparing to install

Refer to AS/NZS 5601.1 for piping size details. These built-in 

cooktops are intended to be inserted in a benchtop cutout.
Only an officially authorised technician should connect the 

appliance.
Before you begin, turn off the gas and electricity supply.

Before connecting the unit, check whether the local connection 

conditions (type of gas) are compatible with the unit’s setting. 

Observe any special conditions imposed by local suppliers 

(utilities). The specifications of this cooktop are stated on the 

data label located on the bottom of the cooktop base.
A duplicate data label is supplied for adhesion to an accessible 

location near the hotplate if the data label on the base of the 

hotplate cannot be accessed when the hotplate is installed.

Clearances

A range hood fitted above the top must be installed according 

to the installation instructions for the range hood. A minimum 

distance of 650 mm is required for a range hood and 750 mm 

for an exhaust fan.
Any adjoining wall surface situated within 200 mm from the 

edge of any hob burner must be a suitable non-combustible 

material for a height of 150 mm for the entire length of the hob. 

Any combustible construction above the hotplate must be at 

least 650 mm above the top of the burner and no construction 

shall be within 450 mm above the top of the burner.

PLQ

PLQ

Summary of Contents for EC945RB91A












Reviews: