Siemens CERBERUS PYROTRONICS PXL Installation, Operation And Maintenance Manual Download Page 40

Page: 40 / 83

PXL Conventional Fire Alarm Control Panel

Installation

Wiring to the PRM-4

Refer to Table 12. Dress the field wiring that will be going to the

PRM-4 terminals. Strip the insulation from the wiring and connect the

wires to the appropriate screw terminals.

TABLE 12

WIRING TO THE OPTIONAL PRM-4

Screw Terminal

Application

TB1

Relays 1-2

TB2

Relays 3-4

STEP 15Install All System Labels

Make sure that all System labels are filled out on the appropriate

printed circuit boards. The following modules require labels:

PCM-1

PZE-4B

- zone label

- terminal block label

Install the

PXL Connection Diagram,

P/N 575-294138, and the

PXL

Alarm Verification Label,

P/N 575-294201, on the inside front cover

of the enclosure.

STEP 16Install the Door to the Backbox

Replace the door on the hinges of the backbox.

STEP 17Power-up the PXL

Turn on the AC power to the System. The power light on the PCM-1

display turns on and the System displays the following message:

DO YOU WANT TO

CONFIGURE THE

SYSTEM NOW ?

<NO

YES>

To configure the System and program the PXL, refer to Chapter 4,

Programming the PXL Control Panel.

Technical Manuals Online! - http://www.tech-man.com

firealarmresources.com

Summary of Contents for CERBERUS PYROTRONICS PXL




















































































Search results

Summary of Contents for CERBERUS PYROTRONICS PXL

Reviews:

Related manuals for CERBERUS PYROTRONICS PXL

Brands by name

Popular brands

Siemens CERBERUS PYROTRONICS PXL, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for CERBERUS PYROTRONICS PXL

Reviews:

Related manuals for CERBERUS PYROTRONICS PXL

Brands by name

Popular brands