manualshive.com logo in svg

Siemens 5WG1 201-2DB12, Technical Product Information

Share
Download
Siemens 5WG1 201-2DB12 Technical Product Information Download Page 9

 

Gamma 

instabus

 

Technical product information 

June 2014 

Gamma arina touch sensor                       single 
 

 

double 

 

 

quadruple 

UP 20x, UP 28x/3 and UP 28x/5 

   

 

  

 

Technical product information 

Siemens Building Technologies 

Subject to change without further notice 

Update: http://www.siemens.com/gamma 

 

 

2.16.1.13/9 

Dimension drawing 

Dimensions in mm 

 

 

 

 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

General notes 

•

 

The operating instructions must be handed over to the 
client. 

•

 

Any faulty device is to be sent together with a return 
delivery note of the local Siemens office. 

•

 

If you have further questions concerning the product 
please contact our technical support. 

  +86 (10) 4006306090 

  [email protected] 

 

Note: 

This product supports two different operation modes: 
KNX and PL-Link. 
This document describes the KNX functionality that can 
be configured with ETS. 
For PL-Link refer to documentation for Desigo. 

Summary of Contents for 5WG1 201-2DB12










Reviews:

No comments

Brands by name

Popular brands

Load more brands