Siemens 5WG1 201-2DB12 Technical Product Information Download Page 7

Page: 7 / 9

Gamma

instabus

Technical product information

June 2014

Gamma arina touch sensor single

double

quadruple

UP 20x, UP 28x/3 and UP 28x/5

Technical product information

Siemens Building Technologies

Subject to change without further notice

Update: http://www.siemens.com/gamma

2.16.1.13/7

Installation of mounting frame (F1)

Mount the mounting frame (F1) onto conduit box (G1)
via mounting slots with mounting screws (F2).

Figure 4: Mounting of the frame

Mounting frame

Mounting screws

Conduit box (86 mm X 86 mm)

Mounting slots

Insert KNX connector (H2)

−

Wiring the KNX connector (H2).

−

Insert the KNX connector (H2) to the touch sensor.
Please be noted the polarity of bus connection with
mark on housing.

Figure 5: Connect KNX connector

Back housing

Front housing

KNX connector

KNX line

Installation of main module (F3 together with F4)

Slip the wall switch's main module (F3) together with
(F4) onto the mounting frame and firmly press them to-
gether.

Figure 6: Mounting of the main module

Mounting frame

Back housing

Front housing

Summary of Contents for 5WG1 201-2DB12










Search results

Summary of Contents for 5WG1 201-2DB12

Reviews:

Brands by name

Popular brands

Siemens 5WG1 201-2DB12, Technical Product Information

Search results

Summary of Contents for 5WG1 201-2DB12

Reviews:

Brands by name

Popular brands