background image

Document No. 129-104 

Installation Instructions 

October 1, 2013 

2200

DC+ ACH

DC- ACN (GND)

Signal Out

CONTROLLER

Sensor Power DC
Common
Signal In

Common

Signal In

SEN0650R1

Isolated DC

Supply 300 MA Max.

I
I
I
I
I

DC+

DC-

AC

IN

Powered By

Controller

See Controller

Installation Instructions

For Power Input

Requirements

2200

DC+ ACH

DC- ACN (GND)

Signal Out

Powered By

Isolated DC

 

Figure 7.  Externally DC Powered 2200 Room Units. 

 

2200

DC+ ACH

DC- ACN (GND)

Signal Out

CONTROLLER

Sensor Power DC
Common
Signal In

Common
Signal In
Common
Signal In
Common

Common

Signal In

SEN0649R1

Class 2

Isolated AC Supply

100 VA Max.

Powered By

Class 2 (100VA)

Isolated AC

I
I
I
I
I

I
I
I
I
I

ACH
ACN

ACH
ACN

ACH
ACN

Powered By

Controller

2200

DC+ ACH

DC- ACN (GND)

Signal Out

2200

100 VA

DC+ ACH
DC- ACN (GND)
Signal Out

Powered By

Class 2 (100VA)

Isolated AC

L    N    E

With Class 2 (100 VA) Output

Isolated AC Supply

(See Controller

Installation Instructions)

L   N   E

Note: See Caution

 

Figure 8.  Externally AC Powered 2200 Room Units. 

NOTE: 

 

 
Externally DC powered 
2200 Room Units require 
isolated DC supply with all 
commons connected and 
may be used on the same 
controller with other Room 
Units powered by Internal 
Sensor Supply. 

NOTE: 

 

 
Externally AC powered 
2200 Room Units require 
controller common and all 
AC secondary neutral ACN 
to be earth grounded and 
may be used on the same 
controller with other room 
units powered by internal 
sensor supply. 

Information in this publication is based on current specifications. The company reserves the right to make changes in specifications and models as 
design improvements are introduced. APOGEE is a registered trademark or Siemens Industry, Inc. Other product or company names mentioned herein 
may be the trademarks of their respective owners. © 2013 Siemens Industry, Inc. 

 

Siemens Industry, Inc. 

Building Technologies Division 
1000 Deerfield Parkway 
Buffalo Grove, IL 60089 
USA 
+ 1 847-215-1000 

Your feedback is important to us. If you have 
comments about this document, please send them 
to 

[email protected]

 

 

Document No. 129-104 

Printed in the USA 

Page 5 of 5

 

Summary of Contents for 2200 Series






Reviews: