Siemens 1PL622 Operating Instructions Manual Download Page 42

Page: 42 / 86

Transport, assembly, and connection

3.3 Electrical connection

A5E00264365A

Siemens AG Operating Instructions 2.02 1PL622

NOTICE

Do not turn the Sensor Module with a pipe wrench or hammer or any similar tool as this

could damage the Sensor Module.
Turn the Sensor Module by hand.

Typical twisting moment:

4 ... 8 Nm

ແ

Figure 3-11 Sensor Module ① mounted on terminal box

NOTICE

Changing the cable outlet direction by any improper means will cause damage to the

connecting cables.
The permissible rotation range must not be exceeded. A maximum of ten changes to the

rotation angle of the Sensor Module are permissible within the rotation range.

[ID 964]

3.3.8

Connecting the temperature sensor

Connection

Connect the wires of the temperature sensor to the speed sensor connector with the aid of

connecting leads (see section entitled "Connecting the speed sensor").

Summary of Contents for 1PL622























































































Search results

Summary of Contents for 1PL622

Reviews:

Related manuals for 1PL622

Brands by name

Popular brands

Siemens 1PL622, Operating Instructions Manual

Search results

Summary of Contents for 1PL622

Reviews:

Related manuals for 1PL622

Brands by name

Popular brands