background image

 18

SE 40/125S ignition protected thruster assembly     

version 1.3 - April 2014

1

. The equipment manufactured by Sleipner Motor AS (The “Warrantor”) is warranted to be free from defects in workmanship and mate-

rials under normal use and service.

2

. This Warranty is in effect for of two years from the date of purchase by the user. Proof of purchase must be included, to establish that 

it is inside the warranty period.

3.

 This Warranty is transferrable and covers the product for the specified time period. 

4

. In case any part of the equipment proves to be defective, other than those parts excluded in paragraph 5 below, the owner should do 

the following:

  (a) prepare a detailed written statement of the nature and circumstances of the defect, to the best of the Owner's knowledge, in-

cluding the date of purchase, the place of purchase, the name and address of the installer, and the Purchaser’s name, adress and 

telephone number;

  (b) the Owner should return the defective part or unit along with the statement referenced in the preceding paragraph to the warran-

tor, Sleipner Motor AS or an authorized Service Centre, postage/shipping prepaid and at the expense of the Purchaser;

  (c) if upon the Warrantor’s or Authorized Service Centre’s examination, the defect is determined to result from defective material or 

workmanship, the equipment will be repaired or replaced at the Warrantor’s option without charge, and returned to the Purchaser at 

the Warrantor’s expense;

  (d) no refund of the purchase price will be granted to the Purchaser, unless the Warrantor is unable to remedy the defect after having 

a reasonable number of opportunities to do so. Prior to refund of the purchase price, Purchaser must submit a statement in writing 

from a professional boating equipment supplier that the installation instructions of the Installation and Operation Manual have been 

complied with and that the defect remains;

  (e) warranty service shall be performed only by the Warrantor, or an authorized Service Centre, and any attempt to remedy the defect 

by anyone else shall render this warranty void.

5.

 There shall be no warranty for defects or damages caused by faulty installation or hook-up, abuse or misuse of the equipment includ-

ing exposure to excessive heat, salt or fresh water spray, or water immersion except for equipment specifically designed as water-

proof. 

6.

 No other express warranty is hereby given and there are no warranties which extend beyond those described in section 4 above. 

This Warranty is expressly in lieu of any other expressed or implied warranties, including any implied warranty of merchantability, 

fitness for the ordinary purposes for which such goods are used, or fitness for a particular purpose, and any other obligations on the 

part of the Warrantor or its employees and representatives.

7.

 There shall be no responsibility or liability whatsoever on the part of the Warrantor or its employees and representatives for injury to 

any person or persons, or damage to property, loss of income or profit, or any other consequential or resulting damage or cost which 

may be claimed to have been incurred through the use or sale of the equipment, including any possible failure or malfunction of the 

equipment, or part thereof.

8. 

The Warrantor assumes no liability for incidental or consequential damages of any kind including damages arising from collision with 

other vessels or objects.

9. 

This warranty gives you specific legal rights, and you may also have other rights which vary from country to country.

Warranty statement

Summary of Contents for SE 40/125 S





















Reviews: