Sidamo TM 200 B User Manual Download Page 14

Page: 14 / 20

User’s manual TM200B

ACCESSORIES AND CONSUMABLE PARTS

8.1.

BASE S2

The bench grinder is designed to be fitted on a base S2

(optional).

Suction

Height x Width x Depth

(mm)

Weight

(kg)

Reference

Not

included

845 x 360 x 360

20198075

8.2.

BASE S2ASP

The grinder is fitted with two outlets to extract dusts.

It is possible to connect a base with a S2 ASP dust
extraction system.

Suction

Power

(kW)

Main power

Rotating

speed

(tr/min)

Air flow

(m³/h)

Depression

(mm H2O)

Noise

level

(dB)

Height x Width x Depth

(mm)

Weight

(kg)

Reference

S2 ASP

included

0,15

1-phase

230 V

2800

290

845 x 360 x 360

20113033

8.3.

DRILL SHARPENER

Additional drill sharpener, designed to be installed on

the bench, next to the grinder :

Sharpening of drills from Ø 3 mm to Ø 18 mm.

Angle adjustment range : from 41° to 88°.

Reference

Drill sharpener

20198072

Summary of Contents for TM 200 B





















Search results

Summary of Contents for TM 200 B

Reviews:

Related manuals for TM 200 B

Brands by name

Popular brands

Sidamo TM 200 B, User Manual

Search results

Summary of Contents for TM 200 B

Reviews:

Related manuals for TM 200 B

Brands by name

Popular brands