SICK UC40 Operating Instructions Manual Download Page 39 | Manualshive

Page: 39 / 46

background image

10.3

Performance

Operating range

UC40-11

2

11x: 65 mm ... 350 mm

UC40-11

3

11x: 200 mm ... 1,300 mm

UC40-11

4

11x: 350 mm ... 3,400 mm

Limiting range

UC40-11

2

11x: 600 mm

UC40-11

3

11x: 2,000 mm

UC40-11

4

11x: 5,000 mm

Measuring object

Natural objects

Resolution

UC40-11

2

11x: ≥ 0.1 mm

UC40-11

3

11x: ≥ 1 mm

UC40-11

4

11x: ≥ 1 mm

Repeatability

± 0.15%

1)

Accuracy

± 1%

2)3)

Temperature compen‐
sation

Temperature compensation

Response time

4)

UC40-11

2

11x: 64 ms

UC40-11

3

11x: 96 ms

UC40-11

4

11x: 160 ms

Switching frequency

UC40-11

2

11x: 10 Hz

UC40-11

3

11x: 7 Hz

UC40-11

4

11x: 4 Hz

Output time

UC40-11

2

11x: 16 ms

UC40-11

3

11x: 24 ms

UC40-11

4

11x: 41.6 ms

Ultrasonic frequency
(typical)

UC40-11

2

11x: 400 kHz

UC40-11

3

11x: 200 kHz

UC40-11

4

11x: 120 kHz

Detection range (typi‐
cal)

Detection ranges

Additional function

Adjustable switching point modes: switching point (Single Point Mode) / switching window (Window
Mode) / background (Window Mode 8%), teachable digital output, parameterizable digital output,
invertible digital output, adjustable switch-on delay digital output, teachable analog output, parame‐
terizable analog output, invertible analog output, automatic switching between current and voltage
output, analog output switchable to second digital output, synchronization of up to 50 sensors,
multiplexing: no mutual interference of up to 50 sensors, adjustable measurement filters: measured
value filter / filter strength / foreground suppression / detection range / sensitivity and sound lobe /
false echo suppression, teach-in buttons (can be deactivated), reset to factory settings

1)

Relative to the current measured value, minimum value ≥ resolution.

2)

Relative to the current measured value.

3)

Temperature compensation can be switched off, not temperature compensated: 0.17% / K.

4)

Subsequent smoothing of the analog output may increase the response time by up to 200% in some applications.

10.4

Interfaces

IO-Link

IO-Link V1.1
Function: Process data, configuration, diagnostics, data storage

Digital output

Quantity: 1
Type: Push-pull: PNP/NPN

1)

Maximum output current I

A

: ≤ 100 mA

TECHNICAL DATA

10

8027772//2022-08-11 | SICK

O P E R A T I N G I N S T R U C T I O N S | UC40

39

Subject to change without notice

«
...
37
38
39
40
41
...
»

Summary of Contents for UC40















































Reviews:

No comments

Related manuals for UC40

Brand: Panasonic Pages: 16

Brand: NEC Pages: 8

Brand: 1byone Pages: 9

Brand: hager Pages: 4

BTL7-S5 B-M Series

Brand: Balluff Pages: 14

BML-S1G0 7 M5E 0 Series

Brand: Balluff Pages: 194

Brand: UniFlow Pages: 42

Brand: Xerox Pages: 2

Brand: Yeti Pages: 19

Brand: veba Pages: 11

Brand: JANE Pages: 21

Brand: Carax Pages: 2

IO-Link BAE SA-CS-027-YI-BP00,3 GS04

Brand: Balluff Pages: 50

Brand: Standby Pages: 10

Brand: BrandMotion Pages: 8

Brand: SICK Pages: 119

Centronic VarioControl VC280

Brand: Becker Pages: 20

Brand: Axxess Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands