SI Pocket Coupled Duo 375 Installation Instructions Manual Download Page 20

20

Programming - RTS 

PROGRAMMING 

- RTS

Each RTS Nano shade includes an installation remote that is used to adjust limits and program 
group controls. These installation remotes are uniquely numbered to the shade they are paired 
with. The lower limit of every shade is preprogrammed to ½” from the bottom of the window. 
After installing each shade, follow these steps to adjust the lower limit: 

STEP 2 - 

Assign shades to groups :

Next, program group controls. To pair with a permanent transmitter 
such as a multichannel Telis or DecoFlex, follow these steps.
1.  Press and hold the program button on the back of the installation  
  remote until the shade jogs.
2.  Select the channel where you want to create a group, then bump  
   (do not hold down) the program button on the back of the remote - 
  the shade will jog.
3.  Both remotes now control the shade.
4.  Continue doing this with each shade until all shades are    

 

  programmed in the desired groups.

NOTE: Each RTS motor can be paired with 12 unique transmitters. 

PROGRAMMING STEPS (must follow in order)
Step 1: Fine tune lower limit
Step 2: Assign shades to groups
Step 3: Pair groups to control system (Mylink, LinkPro)

1.  Beginning with the first shade, pull plastic tab from remote and press      allowing shade to run   
  to lower limit set at the factory.

2.  When shade has stopped, adjust the lower limit by holding      and      simultaneously until the    
  shade jogs.
3.  Use      or      to move the shade to the desired lower limit.
4.  Hold the

 “My”

 button until the shade jogs again.

5.  Repeat this procedure at each window until all shades have lower limits set to desired 

positions.

1.  Download the myLink app.
2.  Pair the grouped shades with LinkPro or MyLink according to the instructions in the myLink app.

STEP 1 - Fine tuning lower limit :

STEP 3 - Pair Groups to control system (LinkPro, myLink) :

       Warning: Do not 
attempt to use any 
installation remote until all 
the shades are installed.

hold the button 

until the shade jogs 

(light on the motor 

turns green).

Installation

Remote

Permanent 

Remote

Bump 

(do not hold)

Summary of Contents for Pocket Coupled Duo 375

























Reviews: