Shuttle FB62 Manual Download Page 80

Page: 80 / 82

- 76 -

Async AGP/PCI CLK

This item allows you to set AGP/PCI clock and CPU clock asynchro-
nous. You can select 66/33, 73/36, or 80/40 to fixed AGP/PCI clock
even if you adjust CPU clock.

The choice: Async by CPU clock, fixed 66/33/100 MHz, fixed 73/
36/100 MHz, fixed 80/40/100 MHz.

****** Vcore ******

CPU Voltage

This item allows you to set CPU Voltage.

The choice: 1.850V~1.100V.

DDR Voltage

This item allows you to set DDR Voltage.

The choice: Auto, 2.65V, 2.70V, 2.75V.

AGP Voltage

This item allows you to set AGP Voltage.

The choice: Auto, 1.55V, 1.60V, 1.65V.

Load Fail-Safe Defaults

When you press <Enter> on this item, you will get a confirmation
dialog box with a message similar to:

Load Fail-Safe Defaults (Y/N) ? N

Pressing 'Y' loads the BIOS default values for the most stable,
minimal performance system operations.

Load Optimized Defaults

When you press <Enter> on this item, you will get a confirmation
dialog box with a message similar to:

Load Optimized Defaults (Y/N) ? N

Pressing 'Y' loads the default values that are factory-set for
optimal performance system operation.

Summary of Contents for FB62



















































































Search results

Summary of Contents for FB62

Reviews:

Related manuals for FB62

Brands by name

Popular brands

Shuttle FB62, Manual

Search results

Summary of Contents for FB62

Reviews:

Related manuals for FB62

Brands by name

Popular brands