Shuttle FB62 Manual Download Page 6

Page: 6 / 82

- 2 -

3.2 JUMPER SETTINGS ................................................................................. 25

JUMPERS & CONNECTORS GUIDE .................................................... 26

Jumpers

Clear CMOS Setting (JP1) ................................................................... 28

Back-Panel Connectors

COM1 Port Connector ........................................................................... 29

VGA Port Connector .............................................................................. 29

USB0/1 Port Connectors ....................................................................... 29

10/100 base-T LAN Port Connector ....................................................... 29

USB2/3 Port Connectors ....................................................................... 29

PS/2 Keyboard & PS/2 Mouse Connectors ............................................ 30

Bass/Center-Out Port Connector ........................................................... 30

Rear-Out Port Connector ...................................................................... .30

Front-Out Port Connector ....................................................................... 30

Front-Panel Connectors

ATX Power On/Off Switch Header (PWON) ............................................ 31

HDD LED Header (HLED) .................................................................... 31

Green LED / Power LED Header (GLED/PLED) .................................. 32

Hardware Reset Header (RST) ............................................................. 32

Front Panel Connector (JP16) ............................................................... 33

Internal Peripherals Connectors

Enhanced IDE and Floppy Connectors ................................................... 34

Serial ATA Connectors ........................................................................... 34

Other Connectors

ATX Power Supply Connector (ATX1 and ATX2) .................................... 35

System and Chipset Fan Connector (FAN1/2/3) ..................................... 36

Audio CD_IN Connector (JP11) (Black) ................................................. 36

Wireless Keyboard and Mouse Headers (JP6) ..................................... 36

Summary of Contents for FB62



















































































Search results

Summary of Contents for FB62

Reviews:

Related manuals for FB62

Brands by name

Popular brands

Shuttle FB62, Manual

Search results

Summary of Contents for FB62

Reviews:

Related manuals for FB62

Brands by name

Popular brands