Shuttle AK32A User Manual Download Page 69

Page: 69 / 79

- 67 -

HDD Power Down

When this item enabled and after the set up time of system inactiv-
ity, the hard disk drive will be powered down while all other de-
vices remain active.

The choice: Disabled or 1 Min~15 Min.

Suspend Mode

When this item enabled and after the set up time of system inactivity, all
devices except the CPU will be shut off.

The choice: Disabled, 1 Min, 2 Min, 4 Min, 6 Min, 8 Min, 10 Min,
20 Min, 30 Min, 40 Min, or 1 Hour.

Video Off Option

When enabled, this feature allows the VGA adapter to operate in a
power saving mode.

Always On

Monitor will remain on during power saving

mode.

Suspend --> Off

Monitor is blanked when the system enters the

Suspend mode.

The choice: Always On or Suspend ->off.

Video Off Method

This determines the manner in which the monitor is blanked.

V/H SYNC+Blank

This selection will cause the system to turn off

the vertical and horizontal synchronization
ports and write blanks to the video buffer.

Blank Screen

This option only writes blanks to the video
buffer.

DPMS Support

Initial display power management signaling.

The choice: V/H SYNC+Blank, Blank Screen, or DPMS Support.

MODEM Use IRQ

This determines the IRQ which the MODEM can use.

The choice: 3, 4, 5, 7, 9, 10, 11, or N/A.

Soft-Off by PWRBTN

Pressing the power button for more than 4 seconds forces the system
to enter the Soft-Off state when the system has "hung.".

The choice: Instant-Off or Delay 4 Sec.

Summary of Contents for AK32A
















































































Search results

Summary of Contents for AK32A

Reviews:

Related manuals for AK32A

Brands by name

Popular brands

Shuttle AK32A, User Manual

Search results

Summary of Contents for AK32A

Reviews:

Related manuals for AK32A

Brands by name

Popular brands