background image

Shure Incorporated

2/15

21. Operate this product within its specified operating temperature range.

This symbol indicates that dangerous voltage constituting a risk of electric shock is present within 

this unit.

This symbol indicates that there are important operating and maintenance instructions in the litera­

ture accompanying this unit.

WARNING: 

This product contains a chemical known to the State of California to cause cancer and birth defects or 

other reproductive harm.

Description

The Shure Model SCM800 is a full­featured, eight­channel microphone mixer for sound reinforcement, general au­

dio recording, and audio­visual systems. Any low­impedance, balanced dynamic or condenser microphone, includ­

ing a wireless microphone system, can be used with the SCM800 mixer

Each SCM800 accepts up to eight microphone­ or line–level inputs and one aux­level input (two input jacks feed

 

the same channel). Up to four SCM800 mixers can be linked to provide up to 32 input channels. Each input chan­

nel has a two-band equalizer, switchable microphone- or line-level operation, switchable 48 V phantom power, and 

a ¼-inch send/ receive insert jack.

The SCM800 operates on 120 Vac power; the SCM800E operates on 230 Vac power. Both models are supplied 

with rack-mounting hardware, link cable and removable block terminal connectors. An accessory rack panel 

adapter (Model RKC800, available separately) converts the removable block input and output connectors to XLR 

connectors, and the Aux connectors to phono jacks.

Features

Compatible with Shure SCM810 and FP410 automatic microphone mixers

Adjustable EQ per channel: low-frequency rolloff and highfrequency shelving

48 V phantom power selectable for each input

Active balanced microphone- and line-level inputs and line-level output

Highly RF-resistant chassis and circuitry

LED indication of channel clipping

Linking capability for systems up to 32 microphones

Two Aux-level input jacks that feed one channel

Insert jack on each channel

Manual mixing of input channels

Front-panel headphones output with level control

Peak-responding output limiter with selectable thresholds and LED indicator

Summary of Contents for SCM800
















Reviews: