background image

Shure Incorporated

11/12

Fax: +49-7262-92 49 11 4

Email: [email protected]

Operation of this device is subject to the following two conditions: (1) this device may not cause interference, and 

(2) this device must accept any interference, including interference that may cause undesired operation of the de­

vice.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de li­

cence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, 

et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est suscepti­

ble d'en compromettre le fonctionnement.

Eligible for CE marking.

Authorized under the verification provision of FCC Part 15B.

CAN ICES-3 (B)/NMB-3 (B)

Industry Canada ICES-003 Compliance Label: 

CAN ICES-3 (B)/NMB-3(B)

Note: 

See the label located on the bottom side of the charger enclosure for the FCC marking, the CE marking, the 

RCM marking, the KC marking, and the electrical ratings.

Note:

 EMC conformance testing is based on the use of supplied and recommended cable types. The use of other 

cable types may degrade EMC performance.

Changes or modifications not expressly approved by Shure Incorporated could void your authority to operate this 

equipment.

Meets requirements of the following standards:

EN55032

EN55103-2

EN55024

EN60950

Korea KN32/35

IEC60950

Please consider the environment, electric products and packaging are part of regional recycling schemes and do 

not belong to regular household waste.

Important Product Information

WARNING: 

Danger of explosion if incorrect battery replaced. Operate only with AA batteries.

WARNING

• Battery packs may explode or release toxic materials. Risk of fire or burns. Do not open, crush, modify, disas­

semble, heat above 140°F (60°C), or incinerate.

Follow instructions from manufacturer

Only use Shure charger to recharge Shure rechargeable batteries

WARNING: Danger of explosion if battery incorrectly replaced. Replace only with same or equivalent type.

Summary of Contents for SBC250













Reviews: