background image

ENGLISH

6

12 dB and 18 dB Output Pads

Each DFR22 output has a 12 dB pad and an 18 dB pad that can be

engaged through the software interface. Use these pads when con-

necting the DFR22 to lower-level inputs. They cannot be used to

prevent clipping at the output stage of the DFR22

NOTE:

 The Output meters indicate the signal level present at the

digital-to-analog converters. The 12 and 18  dB pads act upon the

signal after the digital-to-analog converters, so the meters do not

reflect the pads.

COMPUTER CONNECTIONS 
RS-232 Connections

Connect the COM port on your computer to the 9-pin RS-232 con-

nector on the front panel of the DFR22, shown in Figure 9, using a

male-to-female serial cable. Pin outs for a 9–pin RS–232 cable are

shown in Figure 10 and listed in Table 1.

NOTE: 

Only the TX, RX, and GND pins need to be connected in

order to communicate with the DFR22.
You can also connect a computer or control system to the 3–pin

RS-232 Phoenix connector on the back panel of the DFR22, as

shown in Figure 11.

IMPORTANT: 

You CANNOT connect two PCs to the DFR22 at the

same time. However, you CAN connect an AMX or Crestron sys-

tem and a PC to the DFR22 at the same time.

RS-232 SERIAL PORT CONNECTION

Figure 9

9-PIN FEMALE

TO COMPUTER

9-PIN MALE

TO DFR22

DFR22 9–PIN RS-232

 FEMALE CONNECTOR

COMPUTER 9-PIN RS-232

 MALE CONNECTOR

RS-232 CABLE PINOUTS

Figure 10

RS-232

PHOENIX RS-232 SERIAL PORT CONNECTION

Figure 11

Table 1.

 RS-232 PIN OUTS

DFR22

COMPUTER

PIN NO.

––

––

1

TX

RX

2

RX

TX

3

––

DTR

4

GND

GND

5

––

DSR

6

––

RTS

7

––

CTS

8

––

––

9

Shure Link Network

Up to 16 Shure Link devices, including the DFR22, DFR11EQ,

DP11EQ, P4800, and UA888, can be linked and controlled from

one computer. Using 5-pin DIN cables, connect the 

Shure Link IN

and 

Shure Link OUT

 of each device, as shown in Figure 12.

NOTE: The last device in the chain MUST be connected to the

first device (the one connected directly to the computer) to

form a loop.

SHURELINK OUT

SHURELINK IN

RS-232

DEVICE ID # 0

DEVICE ID # 1

DEVICE ID # 2

SHURELINK NETWORK CONNECTIONS

Figure 12

Summary of Contents for DFR22E














Reviews: