SHOWTEC White-PIX V1 Manual Download Page 10 | Manualshive

Page: 10 / 28

background image

9

Ordercode: 42278

White-PIX

Set Up and Operation

Follow the directions below, as they pertain to your preferred operation mode.
Before plugging the unit in, always make sure that the power supply matches the product specification
voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.
Connect the device to the main power supply.

Vertical Installation of White-PIX

It is possible to install multiple White-PIX devices by attaching them to each other in a vertical position.
Follow the instructions below to carry out the installation process.

Fig. 03

01)

Loosen the mounting screws on the White-PIX #1 and release the mounting rail.

02)

Insert the mounting rail in the slot on the White-PIX #2.

03)

Tighten the mounting screws to secure both White-PIX in position.

04)

Secure the installation, using a safety cable and clamps.

The mounting rails enable seamless installation of the fixtures.

You can attach up to 10 devices.

«
...
8
9
10
11
12
...
»

Summary of Contents for White-PIX V1





























Reviews:

No comments

Related manuals for White-PIX V1

Brand: XAG Pages: 24

Brand: UFO Pages: 16

Brand: A.MENARINI Pages: 2

Coronis 5MP Mammo

Brand: Barco Pages: 4

Brand: Barco Pages: 167

Color Coronis 2MP

Brand: Barco Pages: 156

Color Coronis 2MP

Brand: Barco Pages: 12

Brand: Barco Pages: 39

Brand: Barco Pages: 158

Brand: Unitary products group Pages: 28

Brand: J.P. SELECTA Pages: 32

Brand: Jet Pages: 12

Brand: TEC Pages: 6

Brand: U Technology Pages: 6

MCX-C15 - MusicCAST Network Audio Player

Brand: Yamaha Pages: 114

Brand: Eleiko Pages: 4

Brand: Heiniger Pages: 164

Brand: Hausmann Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands