background image

 

Warning

 

 
 
 
 
 

Unpacking Instructions 

Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure 
that all parts are present, and have been received in good condition. Notify the dealer immediately and 
retain packing material for inspection if any parts appear damaged from shipping or the carton itself 
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be 
returned to the factory, it is important that the fixture be returned in the original factory box and packing. 

 

Your shipment includes: 

• Spectral 2500 Zoom Tour

 

• 1X safety cable 
• User manual

 

 
 
 

LED Expected Lifespan 

LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to the acceleration 
of this decline. Packaged in clusters, LEDs exhibit higher operating temperatures than in ideal or singular 
optimum conditions. For this reason when all color LEDs are used at their fullest intensity, life of the LEDs is 
significantly reduced. It is estimated that a viable lifespan of 40,000 to 50,000 hours will be achieved 
under normal operational conditions. If improving on this lifespan expectancy is of a higher priority, place 
care in providing for lower operational temperatures. This may include climatic-environmental and the 
reduction of overall projection intensity. 

 

Safety Instructions 

Every person involved with the installation, operation and maintenance of this device has to: 

-

 

be qualified 

-

 

follow the instructions of this manual 

 
 
 
 
 
 

Before your initial start-up, please make sure that there is no damage caused by transportation. Should 
there be any, consult your dealer and do not use the device. 
 
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to 
follow the safety instructions and warning notes written in this manual. 
 
Please consider that damages caused by manual modifications to the device are not subject to 
warranty. 
 
This device contains no user-serviceable parts. Refer servicing to qualified technicians only. 
 

IMPORTANT:

 

The manufacturer will not accept liability for any resulting damages caused by the non-
observance of this manual or any unauthorized modification to the device. 

 

 

CAUTION! Be careful with your operations. 

With a dangerous voltage you can suffer 

a dangerous electric shock when touching the wires!

 

 

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY  

BEFORE YOUR INITIAL START-UP!

 

 

Summary of Contents for Spectral 2500 Zoom Tour
































Reviews: