7.3 Preset OFF Time
Press PAGE button and DOWN button(on the touch toggle) simultaneously
and hold on for about 2 seconds, all the LED indicators flash once, means
ready to set
OFF Time and the DOWN button is lit.
Preset
Press the corresponding button of
1~8, say
1, the LED indicators
inside the touch toggle show the OFF Time of
1. Rotate the touch toggle
to change the
OFF Time. When
Preset
Preset
Preset
Preset
you are satisfied with the setting, press
and hold on Preset1 button for 2s, all the LED indicators flash once, means the
time setting is complete.
Repeat Step1~Step2 to set OFF time for the rest
s.
PRESET
In step 2 of 7.3.1, press the corresponding button of
1~8, if the DOWN
button flashes repeatedly, it means the
OFF Time is disabled. To enable
the setting, press and hold on UP button and the corresponding
button
for about 2s until all the LED indicators flash once, then release the buttons.
Preset
Preset
Preset
To disable OFF time setting for a
, hold on pressing the corresponding
button of
1~8 and DOWN button for 2seconds, then release the buttons.
Preset
Preset
Press PAGE button and DOWN button simultaneously and hold on for 2 seconds
until all the LED indicators flash once, means exit from OFF Time Setting.
Operation Guide
10
7.3.1 Setting Preset OFF Time
7.3.2 Enable/Disable Preset OFF Time
7.3.3 Exit
Step 1:
To set OFF Time for
s, simply take the following steps:
Preset
Step 2:
Step 3:
The Preset, including SHOW and SCENE, will start to display at its ON time.
If you don't change the setting, the Preset will end the performance at its OFF
time. However, if you change the SHOW or/and SCENE manually during the
display, the Preset will end, not at its OFF time, but at the time when another
Preset ON time takes effect.
NOTE:
5. CURTAIN and SCREEN
The indicators of the CURTAIN and SCREEN directly indicate the working state of
the CURTAIN and SCREEN. In this mode, DA-U-48 can connect a DR-1 as its
Curtain & Screen driver. (For further information, please refer to the user instructions
of DR-1.)
1)
he indicator of
lights up, which
indicates that the
is ON(the
is open).
Press Curtain/Screen button once, t
Curtain/Screen
Curtain/Screen
Curtain/Screen
3) Press
button once again, the indicator of
black out,
which indicates that the
is OFF(the
is closed).
Curtain/Screen
Curtain/Screen
Curtain/Screen
Curtain/Screen
Note:
While processing Saving Scene, the control of Curtain and Screen can be posted at
the same time, the control of Curtain/Screen and AMPLIFIER are the designated
channels.
Playing a PRESET
4.1
4. PRESET
Press the SHOW/PRESET button, the LED indicators of channel button 1~8 light
with blue-white (which is the same as the color of the SHOW/PRESET button),
means the channel button 1~8 switches to the function button of PRESET 1~8.
Press the corresponding button of Preset 1~8 may raise the show which has been
stored in it. Meanwhile it will trigger the Scene which has been assigned in the button.
If no Scene assigned in, the button will flash repeatedly for 5 seconds.
a SCENE to a PRESET
4.2 Assigning
Press the SCENE button desired to designate, say SCENE 3, then press the PRESET
button which you prefer to assign the SCENE in, say PRESET 2, hold on the PRESET
2 button for 2 seconds, all the indicators flash once, the designation is complete. The
SCENE 3 will be raised when you press the PRESET 2 button.
Operation Guide
7
2) Hold on pressing the UP/DOWN button on the touch toggle to adjust the
position of
.
Curtain/Screen
4.3 Removing a SCENE from a PRESET
Press the corresponding button of PRESET 1~8 and hold on for about 4s, until
all the indicators flash once. Then the SCENE assigned by user is removed
from the PRESET button.
The factory settings assign the SCENE1~8 to PRESET 1~8 respectively.
Scene1 corresponds to Preset1, Scene2 corresponds to Preset 2 and the rest
can be deduced from this.
