background image

 

 

 

7 

 

  

 

 

Compact Par 7 Q4 

Product code: 42582 

 

WARNING 
Risk of epileptic shock 

Strobe lighting can trigger seizures in photosensitive epilepsy. Sensitive persons should avoid looking at 
strobe lights. 

 

Attention 
Power supply 

 

Before connecting the device to the power supply, make sure that the current, voltage and 
frequency match the input voltage, current and frequency specified on the information label on the 
device. 

 

Make sure that the cross-sectional area of the extension cords and power cables is sufficient for the 
required power consumption of the device. 

 

Attention 
General safety
 

 

Do not insert objects into the air vents. 

 

Do not connect the device to a dimmer pack. 

 

Do not switch the device on and off in short intervals. This decreases the device’s life. 

 

Do not shake the device. Avoid brute force when installing or operating the device. 

 

Change the lens or the LEDs if they are visibly damaged to such an extent that their effectiveness is 
impaired, for example by cracks or deep scratches. Contact your Highlite International dealer for 
more information, as servicing can be performed only by instructed or skilled persons. 

 

If the device is dropped or struck, disconnect the device from the electrical power supply 
immediately. 

 

If the device is exposed to extreme temperature variations (e.g. after transportation), do not switch it 
on immediately. Let the device reach room temperature before switching it on, otherwise it may be 
damaged by the formed condensation. 

 

If the device fails to work properly, discontinue the use immediately. 

 

Attention 
For professional use only 
This device shall be used only for the purposes it is designed for. 

This device is designed to be used as a professional stage light effect. Any incorrect use may lead to 
hazardous situations and result in injuries and material damage. 

 

This device is not suitable for households and for general lighting. 

 

This device is not designed for permanent operation. 

 

This device does not contain user-serviceable parts. Unauthorized modifications to the device will 
render the warranty void. Such modifications may result in injuries and material damage. 

 

 

Summary of Contents for compact par 7 q4

































Reviews: