Shop fox SHOP FOX W1770 Owner'S Manual Download

Page: 59 / 72

-57-

W1770 21" Bandsaw w/Foot Brake

Troubleshooting

This section covers the most common problems and corrections with this type of

machine.

WARNING!.DO.NOT.make.any.adjustments.until.power.is.disconnected.and.

moving.parts.have.come.to.a.complete.stop!

PROBLEM

POSSIBLE.CAUSE

CORRECTIVE.ACTION

Machine does not start or a
breaker trips.

1.  Key is turned to "0".
2.  Stop/reset button engaged.
3.  Plug/receptacle is at fault or wired

incorrectly.

4. Motor connection wired incorrect-

ly.

5. Thermal protection circuit breaker

amperage is set too low or motor is
at fault.

6. Power supply is at fault/switched

OFF.

7. Motor ON/OFF switch is at fault.
8. Wiring is open/has high resistance.

9. Start capacitor is at fault.
10. Motor is at fault.
11. Wheel cover limit switch is not

closed, wheel covers are open.

12. Foot brake limit switch is at fault

or is pressed down (switch is not
closed).

1.  Turn key to "1".
2.  Rotate clockwise until it pops out/replace.
3.  Test for good contact or correct the wiring.

4. Correct motor wiring connections (

Page 56).

5. Unplug machine, open magnetic switch cover, turn

amperage dial on Thermal Protection Circuit Breaker
to a higher amperage setting. If switch is maxed out,
replace motor.

6. Ensure hot lines have correct voltage on all legs and

main power supply is switched ON.

7. Replace faulty ON/OFF switch.
8. Check for broken wires or corroded/disconnected

connections, and repair/replace as necessary.

9. Test/replace if faulty.
10. Repair/replace.
11. Close wheel covers.

12. Repair/replace limit switch, or stop pressing foot

brake.

Machine stalls or is under-
powered.

1. Wrong workpiece material.

2. Feed speed too fast for task.

3. V-belt slipping.

4. Blade is slipping on wheels.

5. Low power supply voltage.

6. Plug/receptacle is at fault.
7. Motor connection is wired incor-

rectly.

8. Motor bearings are at fault.

9. Motor has overheated.
10. Motor is at fault.

1. Use wood with correct moisture content, without

glues, and little pitch/resins.

1. Decrease feed speed. See

Basic Cutting Tips on

Page 34.

3. Replace bad V-belt, align pulleys, and re-tension

(

Page 47 & 48).

4. Adjust blade tracking and tension to factory specifi-

cations. See

Page 17 or 22.

5. Ensure all hot lines have correct voltage on all

legs.

6. Test for good contacts and correct wiring.
7. Correct motor wiring connections (

Page 56).

8. Test by rotating shaft; rotational grinding/loose

shaft requires bearing replacement.

9. Let motor cool, clean it off, and reduce workload.
10. Repair/replace.

Motor.&.Electrical

Summary of Contents for SHOP FOX W1770









































































Search results

Summary of Contents for SHOP FOX W1770

Reviews:

Related manuals for SHOP FOX W1770

Brands by name

Popular brands

Shop fox SHOP FOX W1770, Owner'S Manual

Search results

Summary of Contents for SHOP FOX W1770

Reviews:

Related manuals for SHOP FOX W1770

Brands by name

Popular brands