Shipping Container Contents
1 Riser
Block
1 Blade
Guard
1
Hex Cap Screw (5/8"-11 x 8-1/2")
2 Flat
Washer
(5/8")
1
Hex Nut (5/8"-11)
1
Guide Post (3/4" Diameter)
1
Blade Guard Assembly
1 Saw
Blade
1 Installation
Instructions
Tools Required for Assembly
26mm Combination Wrench
15/16" Socket w/Ratchet Handle
#1 Cross-point Screwdriver
6" Adjustable Wrench
Hex Wrench Set
Installation Instructions and Parts
JRB-14A Riser Block Kit
# 708717A
(Note: Contains 3/4” guide post, fits model 708113A
Band Saw with 14” x 14” table)
Installation Instructions
1. Disconnect band saw from the power source.
2. Loosen the blade tension, open both blade wheel
covers, remove the table pin and blade insert,
and remove the blade. See the band saw
operator's manual for further details, if necessary.
3. Remove the plastic blade guard next to the
switch box.
4. Remove the switch box assembly and the wire
clamp from the saw arm.
Support the saw arm before
proceeding with the next step!
The saw arm is heavy! Failure to comply may
cause bodily injury and/or damage to property!
5. Carefully loosen the bolt and nut assembly that
hold the saw arm to the saw body and remove.
Remove the saw arm.
6. Place the riser block on the saw body, making
sure the pins in the body line up with the holes in
the riser block.
Note:
The direction-indicating arrow on the riser
block goes to the rear of the machine.
7. Place the saw arm on top of the riser block,
making sure the pins and holes line up. Fasten
the arm to the riser block assembly by inserting
the 5/8-11 x 8-1/2 hex cap screw and 5/8 washer
through the arm, riser block, and saw body and
fasten with a 5/8 washer and 5/8 hex nut. Tighten
the nut securely.
8. Fasten the new blade guard assembly (Item #2,
Figure 1) to the saw arm and saw body.
9. Fasten the switch box assembly to the tapped
holes in the riser block using the same screws
that attached the box to the saw arm. Do not try
to attach the switch box back in the original
position on the saw arm.
10. Loosen the two hex cap screws holding the metal
blade guard assembly to the upper blade guide
bracket (B, Figure 2) and remove the blade
guard.
11. Remove the upper blade guide bracket (B, Figure
2) from the guide post (D, Figure 2).
12. Loosen the guide post lock knob (A, Figure 2).
Loosen, but do not remove set screw (C, Figure
2) to release tension on the guide post.
Note:
Behind the set screw is a spring and steel
ball. Removal of the set screw may cause loss of
the spring and steel ball. Place the new guide
post on top of the one to be removed. Make sure
v-grooves of both guide posts are lined up.
Remove the original by pushing down on top of it
with the replacement. Make sure the
replacement follows the original smoothly.
Note:
Removal of the original guide post without
direct replacement of the new guide post will
cause the spring and ball to fall out of the arm,
making replacement more difficult.
13. Tighten set screw (C, Figure 2).
JET
427 New Sanford Road
LaVergne, Tennessee 37086
Part No. M-708717A
Ph.: 800-274-6848
Rev B1 10/2018
www.jettools.com
Copyright © JET, a division of JPW Industries, Inc.
WARNING:
This product can expose you to
chemicals including lead which is known to the
State of California to cause cancer and birth
defects or other reproductive harm. For more
information go to http://www.p65warnings.ca.gov.
