Shop fox D2260A Instruction Sheet Download Page 12

Page: 12 / 12

-12-

D2260A Mini Mobile Base Instructions

Push the machine from the lowest possible point to

avoid tipping it over and move it to its new location.

Tip:

The best control is usually achieved by pushing

on the side with the swivel casters.

— If the machine is very large, get an assistant to

help stabilize the machine while it is being moved.

Turn the knobs until the feet touch the floor, then

turn the knobs at least an additional half turn. This

will ensure that the major load of the machine is on

the feet rather than on the casters.

Check the machine to make sure it is stable in its

new location, and make sure the machine is clear of

any obstructions before re-connecting the power and

turning the machine

REF PART #

DESCRIPTION

REF PART #

DESCRIPTION

XD2260A001 SWIVEL CASTER

XPB03M

HEX BOLT M8-1.25 X 16

XD2260A002 FIXED CASTER

XPW01M

FLAT WASHER 8MM

XD2260A003 RAIL 10-5/8" LONG

XPLW04M

LOCK WASHER 8MM

XD2260A004 RAIL 15-1/8" LONG

XPN03M

HEX NUT M8-1.25

XPB03M

HEX BOLT M8-1.25 X 16

XD2260A014 RIGHT CORNER BRACKET W/FOOT POST

XPLN04M

LOCK NUT M8-1.25

XD2260A015 RIGHT CORNER BRACKET

XD2271012

SHOP FOX LOGO LABEL

XD2260A016 LEFT CORNER BRACKET W/FOOT POST

XD2058A008 FOOT WITH MAGNET

XD2260A017 LEFT CORNER BRACKET

XD2058A009 KNOB M12-1.75

XD2058A018 TIGHTEN FEET WARNING LABEL

(

)

()

((

=IFEK

I@>?K

I<8I

C<=K

D2260A Parts

Before moving the machine and mobile

base, check to make sure the pathway is

clear of any hoses, wires, tools or shop

debris. An abrupt impact with an object

in the path of travel can lock a wheel

and cause the machine to fall over,

resulting in serious personal injury.

Disconnect the machine from any power

supply or dust collection system before

moving.

Summary of Contents for D2260A













Search results

Summary of Contents for D2260A

Reviews:

Related manuals for D2260A

Brands by name

Popular brands

Shop fox D2260A, Instruction Sheet

Search results

Summary of Contents for D2260A

Reviews:

Related manuals for D2260A

Brands by name

Popular brands