Assembly of Building -
PLEASE READ INSTRUCTIONS PRIOR TO ASSEMBLY
B
-
Fit Window Insert C1
(from top)
1 Place one hinge
on the inner
rebate part of the
top of the
window. The
rounded part of
the hinge should
sit above the
outer edge of the
window. Screw the inner piece into
position using the pre drilled holes
in the hinge and 2x 25mm screws.
Repeat.
C
-
Front Assembly
D
-
Wall Assembly
E
-
Gable Assembly
1 Lay wing panels 'B1' on a flat, clean
surface with framework facing
upwards.
2 Take two lengths of framework 'B3'
44x44x1980 mm. Place one at
each end of wing panels 'B1', to run
flush with both outer edges of parts
'B3'.
3 The horizontal gap where the doors
are to go should measure 1360
mm.
4 Drill/screw parts 'B1' and 'B3' at
both ends using a total of 8x 60 mm
screws.
A
-
Floor Assembly
1 Take one floor panel 'A' and a piece
of framework 34x46x1980 mm
approx 'A1'. Place the framework
on the edge of the floor so that the
framework is flush and level with
the boarding and joists. Mark
where the floor joist meet the
framework and mark. Drill at these
marks. Secure to floor using 6x 60
mm screws.
2 Repeat item 1
with one
more floor
section.
3 Place floors on your firm level base,
board side up. Take 5 pieces
framework 'A2', 34x46x345 'A2' and
place between each floor joist. Nail
half of the widest part to the floor
using 3x 40 mm nails per piece.
4 Once all frameworks are fitted
between floor joists slide another
floor on top of the framework and
secure again using 3x 40 mm nails
per floor joist.
2 Place the window
into the aperture.
Secure the window
to the panel using
3x 25mm screws
per hinge, again
through the
predrilled holes in
the hinge. Repeat.
3 Open the window and fit a further 2x
25mm screws per hinge next to the
one already fitted in Step 1. Repeat.
1 Decide where the window panel is
to go. Place one side panel 'B' on
the floor at the right hand corner.
Place a further panel 'B' inside the
panel already in place. THE
PANELS ALONG THE BACK WALL
SHOULD EXTEND FROM FLOOR
EDGE TO FLOOR EDGE. The
panels to go at the side screw TO
and fit INSIDE the panels to go at
the back.
2 Drill 2 holes, one to the top and one
to the bottom. Do not drill into
adjacent panels. Secure the panels
together using 2x 60 mm screws.
5 Fit the Casement
Stay on the
window using 2x
25mm screws.
6 Mark where the
‘pins’ will be
placed.
7 Secure into
position using
4x 25mm screws
- 2 in each pin.
4
Fitting the Casement Stay.
Place
the casement stay centrally on the
inside of the window. Place the 2
pins under the casement stay.
Position so that it is not resting on
the framework of the panel and not
so high that the pins are of no use.
1 Place one gable section 'F' on top
of the back walls. Drill 4 times
along the length and secure using
4x 60 mm screws.
2 Repeat at front.
G
-
Fit Roof Panels
1 On short edge of each OSB roof
section 'H' attach one piece of
framework 'H2'. This should be
flush with all outer edges. Nail in
position using 4x 40 mm nails per
piece. Repeat.
2 Place both panels on the walls at
the back, flush and even with the
back wall and flush at the ridge.
F
-
Fit Roof Bearers
1 Take 4 roof bearers 34x34x
2070 mm 'G'.
2 Place in opposite guide holes of
both gables.
3 Drill and screw bearer to gable
using 1x 60 mm screw.
IMPORTANT ENSURE GABLE IS
AT 90'. Repeat for all roof bearers.
4 Drill/screw roof bearers at ridge
together using 4x 60 mm screws.
