background image

6

An Emission Control Label is located on the engine. (This is an EXAMPLE ONLY, information on label varies by en-

gine FAMILY).

PRODUCT  EMISSION  DURABILITY  (EMISSION COMPLIANCE PERIOD)

The 50 or 300 hour emission compliance period is the time span selected by the manufacturer certifying the en-

gine emissions output meets applicable emissions regulations, provided that approved maintenance procedures 

are followed as listed in the Maintenance Section of this manual.

Specifications

Model

T282

Engine Type

Air cooled, two stroke, single cylinder gasoline engine

Dry Weight (Without guard and strap)

6.6 kg  / 14.7 lb

Dimensions

1775 x 314 x 345 mm / 69.9 x 12.4 x 13.6 in.

Bore x Stroke

1.38 x 1.18 in./ 35 x 30 mm

Displacement

28.9 cc/1.7 cu. in.

Fuel/Oil Ratio

50:1 Shindaiwa Red Armor® ISO-L-EGD (ISO/CD 13738) and J.A.S.O.

M345- FD, two-stroke, air-cooled engine oil.

Fuel Tank Capacity

750 ml/25.4 oz.

Carburetor Type

Diaphragm-type carburetor

Ignition

One-piece electronic, transistor-controlled

Spark Plug

BPMR6A  

                                                 Spark Plug Gap

0.6  mm  (0.024 in)

                                                               Torque

16.7 - 18.6 N∙m  (148-165 in • lbf)

Air Cleaner Type

 Non-reversible foam filter element

Starting Method

Recoil

Stopping Method

Slide switch

Transmission Type

Automatic, centrifugal clutch w/bevel gear

Engine Idle Speed

3,000 RPM

Clutch Engagement Speed

3,800 RPM

Wide Open Throttle Speed (W.O.T.)

9,600 RPM

*Specifications are subject to change without notice.

Emission Control (Exhaust & Evaporative)

EPA 2010 and Later

The emission control system for the engine is EM (engine modification) and, if the second to last character of the 

Engine Family on the Emission Control Information label (sample below) is “B”, “C”, “K”, or “T”, the emission control 

system is EM and TWC (3-way catalyst). The fuel tank/fuel line emission control system is EVAP (evaporative emis-

sions). Evaporative emissions for California models are only applicable to fuel tanks.

IMPORTANT ! 

This spark ignitioin system complies with the Canadian standard ICES-002.

Summary of Contents for T282





























Reviews: