manualshive.com logo in svg

Shindaiwa C242S, Owner'S/Operator'S Manual

Share
Download
Shindaiwa C242S Owner'S/Operator'S Manual Download Page 21

Declaration of Conformity

DECLARATION

OF

CONFORMITY

   We hereby declare the Shindaiwa Engine Brushcutter,
   Model R242 (T242XS/EC2, C242S/EC2),

   meets the following respective requirements.

   Council Directives: 

 

 

 

Standard taken:

   89/336/EEC as amended 

 

 

  ISO 12100- 1&2

   98/37/EC as amended   

 

 

  ISO 11806

   2000/14/EC as amended 

 

 

  CISPR 12

   2004/26/EC as amended

   Measured sound power level: 109dB(A)

   Guaranteed sound power level: 110dB(A)

   Technical documentation is kept by:
   K. Maeda  DIV. Manager
   Engineering Research and Development DIV.

                           

Shindaiwa Corporation

Head office : 6-2-11, Ozuka-Nishi, Asaminami-Ku,

 

 

 

 

 

 

Hiroshima, 731-3167, Japan

TEL: 81-82-849-2003, FAX: 81-82-849-2482 

   2 March, 2007

 

 

 

 

 

 

  

Shindaiwa Corporation

   T. Yoshitomi
   DIV. Manager    

 

 

Head office : 6-2-11, Ozuka-Nishi, Asaminami-Ku,

   Quality Assurance DIV. 

 

 

 

 

Hiroshima, 731-3167, Japan

 

 

 

 

 

 

 

TEL: 81-82-849-2206, FAX: 81-82-849-2481

No. 0095

21

Summary of Contents for C242S

























Reviews:

No comments

Brands by name

Popular brands

Load more brands