Shindaiwa 80465 Owner'S/Operator'S Manual Download Page 9

Page: 9 / 24

CULT03

READ THE

OPERATOR’S MANUAL.

WEAR HEARING AND ANSI Z87.1

APPROVED EYE PROTECTION.

KEEP AWAY FROM

ROTATING TINES.

80278

Shindaiwa Inc.

Tiller/Cultivator Kit Contents

Debris Shield and Bracket

Assembly

Plastic Sleeve

■

4mm hex wrench

■

5mm hex wrench

■

Pliers

■

7/16" wrench (socket wrench
recommended)

Hitch

Pins

Clevis Pins

Tiller/Cultivator Tine and

Holder Assemblies

Required Tools

Gearcase

Kit Contents

80275

(All PowerBrooms) Includes

Tines, Debris Shield, mounting
hardware and caution label.

99909-44000

(T230 T231 Trim-

mers) Includes Gearcase, Tines,
Debris Shield, mounting hardware
and caution label.

99909-55000

(T270 T272 Trim-

mers) Includes Gearcase, Tines,
Debris Shield, mounting hardware
and caution label.

Figure 4

DESCRIPTION

Item

No.

Qty.

Description

Debris Shield and
Bracket Assembly

Plastic Sleeve

Tiller/Cultivator Tine
and Holder Assembly

Clevis Pins

Hitch Pins

Caution Label

Caution

Label

Summary of Contents for 80465

























Search results

Summary of Contents for 80465

Reviews:

Related manuals for 80465

Brands by name

Popular brands

Shindaiwa 80465, Owner'S/Operator'S Manual

Search results

Summary of Contents for 80465

Reviews:

Related manuals for 80465

Brands by name

Popular brands