background image

11

IMPORTANT!

MAINTENANCE, REPLACEMENT, OR 

REPAIR OF EMISSION CONTROL DEVIC-

ES AND SYSTEM MAY BE PERFORMED 

BY ANY REPAIR ESTABLISHMENT OR 

INDIVIDUAL. HOWEVER, WARRANTY 

REPAIRS MUST BE PERFORMED BY A 

DEALER OR SERVICE CENTER AUTHO-

RIZED BY SHINDAIWA CORPORATION 

AND USE OF PARTS THAT ARE NOT 

EQUIVALENT IN PERFORMANCE AND 

DURABILITY TO AUTHORIZED PARTS 

MAY IMPAIR THE EFFECTIVENESS OF 

THE EMISSION CONTROL SYSTEM AND 

MAY HAVE A BEARING ON THE OUT-

COME OF THE WARRANTY CLAIM.

General Maintenance

WARNING!

Operating the engine without a muffler 

or with a muffler that is damaged or im

-

properly installed can increase engine 

noise sufficiently to cause hearing loss.

Muffler

Prior to each work day, perform the follow-

ing:

n

  Remove all dirt and debris from the 

engine, check the cooling fins and air 

cleaner for clogging, and clean as neces-

sary. See Figure 16.

Daily Maintenance

WARNING!

 

 Always wear gloves when 

working around the cutter assembly.

n

  Clean any debris or dirt from the hedge 

trimmer cutter blades. Lubricate the 

blades before use and after refueling. 

Check the cutters for damage or incor-

rect adjustment.

n

  Check for loose or missing screws or 

components. Make sure the cutter at-

tachment is securely fastened.

n

  Check the entire machine for leaking 

fuel or grease.

n

  Make sure nuts, bolts, and screws (ex-

cept carburetor adjusting screws) are 

tight.

Figure 16

Keep cooling 

fins clean

Keep air 

passages 

clean

WARNING!

Non-standard parts may not operate 

properly with your unit and may cause 

damage and lead to personal injury.

IMPORTANT!

Using non-standard replacement parts 

could invalidate your Shindaiwa warranty.

WARNING!

Before performing any maintenance, 

repair, or cleaning work on the 

machine, make sure the engine and 

cutting attachment are completely 

stopped. Disconnect the spark plug 

wire before performing service or 

maintenance work.

This machine must never be operated with 

a faulty or missing spark arrestor or muf-

fler. Make sure the muffler is well secured 

and in good condition. A worn or damaged 

muffler is a fire hazard and may also cause 

hearing loss.

Spark Plug

Keep the spark plug and wire connections 

tight and clean.

n

  Carefully remove any accumulations of 

dirt or debris from the muffler and fuel 

tank. Check cooling air intake area at 

base of crankcase.  Remove all debris. 

Dirt build-up in these areas can lead to 

engine overheating, fire, or premature 

wear.

Summary of Contents for 68800-94313





















Reviews: