Shindaiwa 68800-94313 Owner'S/Operator'S Manual Download Page 4

4

CAUTION!

n

  Always maintain the articulated 

hedge trimmer according to this 

owner’s manual and follow the 

recommended scheduled mainte-

nance. 

n

  Never modify or disable any of the 

hedge trimmer’s safety devices.

n

  Always use genuine Shindaiwa 

parts and accessories when repair-

ing or maintaining this machine.

n

  Do not make unauthorized modi-

fications to the articulated hedge 

trimmer.

n

  Never allow the engine to run at 

high RPM without a load. Doing so 

could damage the engine.

n

  When transporting the hedge trim-

mer in a vehicle, tie it down securely 

to prevent fuel spillage or damage 

to the machine.

n

  Always stop the engine and allow 

it to cool before refueling. Avoid 

overfilling and wipe off any fuel that 

may have spilled.

n

  Never place flammable material 

close to the engine muffler and 

never run the engine without the 

spark arrestor screen in place.

n

  Always clear your work area of 

trash or hidden debris to help en-

sure good footing.

n

  Keep the cutters sharp and properly 

adjusted.

n

  Keep the articulated hedge trimmer 

as clean as possible. Keep it free of 

loose vegetation, mud, etc.

Wear sturdy footwear with nonslip 

soles to provide good footing. 

Steel-toed safety boots are recom-

mended. Never operate machine 

bare-footed.

Operating the Articulated Hedge Trimmer

Figure 2

Keep bystanders at least 50 feet 

(15 meters) away from the operat-

ing trimmer to reduce the risk of 

being struck by falling objects or 

thrown debris.

Always operate with 

both hands firmly grip-

ping the machine.

Wear non-slip heavy-duty 

gloves to improve your 

grip on the trimmer handle. 

Wear snug-fitting clothes 

that also permit freedom of 

movement. NEVER wear 

shorts!

Always wear a hard hat to reduce 

the risk of head injuries during 

operation of this machine.

Always wear eye and hearing protec-

tion. Shindaiwa recommends wearing 

a face shield as additional face and 

eye protection.

Keep a proper footing and do not 

overreach—maintain your balance 

at all times during operation.

Secure long hair 

so it is above 

shoulder level.

Summary of Contents for 68800-94313





















Reviews: