background image

4

CAUTION!

n

  Always maintain the articulated 

hedge trimmer according to this 

owner’s manual and follow the 

recommended scheduled mainte-

nance. 

n

  Never modify or disable any of 

the hedge trimmer’s safety de-

vices.

n

  Always use genuine Shindaiwa 

parts and accessories when 

repairing or maintaining this ma-

chine.

n

  Do not make unauthorized modi-

fications to the articulated hedge 

trimmer.

n

  Never allow the engine to run at 

high RPM without a load. Doing 

so could damage the engine.

n

  When transporting the hedge 

trimmer in a vehicle, tie it down 

securely to prevent fuel spillage 

or damage to the machine.

n

  Always stop the engine and allow 

it to cool before refueling. Avoid 

overfilling and wipe off any fuel 

that may have spilled.

n

  Never place flammable material 

close to the engine muffler and 

never run the engine without the 

spark arrestor screen in place.

n

  Always clear your work area of 

trash or hidden debris to help 

ensure good footing.

n

  Keep the cutters sharp and prop-

erly adjusted.

n

  Keep the articulated hedge trim-

mer as clean as possible. Keep it 

free of loose vegetation, mud, etc.

Operating the Articulated Hedge Trimmer

Figure 3

Wear sturdy footwear 

with nonslip soles to provide 

good footing. Steel-toed 

safety boots are recommend-

ed. Never operate machine 

bare-footed.

Keep a proper footing and do not 

overreach—maintain your balance 

at all times during operation.

Keep bystanders at least 50 feet 

(15 meters) away from the  

operating trimmer to reduce the 

risk of being struck by falling 

objects or thrown debris.

Always operate with 

both hands firmly  

gripping the machine.

Wear non-slip heavy-duty 

gloves to improve your 

grip on the trimmer handle. 

Wear snug-fitting clothes 

that also permit freedom  

of movement. NEVER  

wear shorts!

Always wear a hard hat to reduce 

the risk of head injuries during 

operation of this machine.

Always wear eye and hearing  

protection. Shindaiwa recommends 

wearing a face shield as additional 

face and eye protection.

Secure long hair 

so it is above 

shoulder level.

Figure 2

Summary of Contents for 62640-94313





















Reviews: