background image

Before  using  the  pump,  please  use  the 
screwdriver  to  toggle  the  fan  blades  to  check 
whether the electric pump rotates smoothly.

The  electric  pump  shall  be  conducted  test  run 
before  use,  and  the  time  shall  not  exceed  10s 
because long-time dry operation will damage the 
mechanical seal. For three-phase electric pump, 
you need to check whether the rotation direction 
is  consistent  with  the  rotation  mark.  In  case  of 
inverse rotation of the electric pump, you should 
cut off the power immediately and adjust any two 
phases of the three phases. 

You  should  set  drainage  ditch  around  the 
electric pump to form natural drainage to avoid 
property  damage  due  to  water  leakage  when 
using,  repairing  and  replacing  the  water  pump 
(especially at the basement, kitchen, stairs and 
other places).

The  electric  pump  should  be  installed  at  places 
where  it  is  convenient  for  checking  and 
maintenance  and  be  kept  dry  and  ventilated. 
When  installing  the  electric  pump  at  narrow 
places,  you  should  install  it  according  to  the 
figure  below  and  the  fan  housing  must  be  at  a 
distance  of  over  25cm  from  the  wall  to  facilitate 
heat dissipation.

Y-shaped Filter

1. When first use it, please be sure to fill the pump 
body  with  water  and  then  plug  in  the  power  to 
avoid dry operation without water.
2. Self-priming  pumps  can  start  with  the  pump 
body  filled  with  water,  do  not  have  to  keep  all 
inlet pipes filled with water, and the inlet pipes of 
non self-priming pumps must be filled with water 
and exhaust all air in pipeline system. 

 For areas with high sand content, it 
is advised to install a Y-shaped filter 
at the inlet pipe to prevent the sand 
from  entering  into  the  pump  body 
and  causing  wearing  or  blocking  of 
the impeller.

NOTICE

Connect the sewer

25cm

25cm

25cm

NOTICE

NOTICE

14

Summary of Contents for AWZB























Reviews: