To change settings, display an appropriate screen and change the setting (value or function) by pressing or key.
On the output monitor screen of basic screens, you can change the control output from “Automatic” to “manual” ,and save its change of setting. Display the output monitor
screen, and then press key for three seconds to shift from Automatic to Manual. Then by pressing or key, you can adjust to the desirable output value. In this case, no
need to press
key in order to determine the change of setting.
Press key for three seconds as well to shift back to Automatic. Excluding when a keylock is OFF, Automatic
⇔
Manual switchover does not work while STBY<RST> and AT
are in operation.
In the case of two-output type, the switchover between automatic and manual is operatable through output 1 and output 2. The setting is altered simultaneously.
4
5. Description of screens
5-1. How to move to another screen
5-2. Setting Method
Every time you press the
key on a basic screen, it shifts to each screen of the basic screens.
Press the
key for 3 seconds on a basic screen, then it shifts to the lead screen of mode 1 screens.
Press the
key on the lead screen of mode 1 screens , then it further advances to mode 2, and mode 3. (Notes: If no corresponding option is found, the mode 4 - 9 is skipped)
Press the
key on the lead screen of mode 1 screens , then it further advances to mode 9, and mode 8. (Notes: If no corresponding option is found, the mode 4 - 9 is skipped)
Press the
key for 3 seconds on the lead screen of mode 1
〜
9 screens, then it shifts to the basic screen.
Press the
key on the lead screen of mode 1
〜
9 screens, then it shifts to the first setting screen of each screens.
Press the
key on the the first setting screen of each screens, then it shifts to the next screen. Every time you press the key, it shifts to the next setting screen.
5-3. Power-on and initial screen display
At power-on, the display section shows each screen of initial screens for one second , then moves on to the basic screen.
Targeted value (PV) is displayed on the upper row as four-digit ,and
target d value (SV) is displayed on the lower row also as four-digit.
(Notes:hereinafter, measured value and targeted value are referred to as
”PV” and “SV”)
At the time of FIX, execution SV is displayed and change of setting is
possible.
PROG’s SV is just displayed ,and change of setting is impossible.
Setting range:
（
）
Control stop [Output OFF (0%)]
operation
conduct of control operation
Choose (RUN) by key. Decide by key, then Monitor LED’s
RUN lights up to start control operation.
Initial value: (stanby)
（
Initial value at the time of constant
value control
）
（
reset
）
(Initial value at the time of program control)
manual output setting range : 0.0-100.0% (within output limiter)
At the time of automatic output, monitor display only.
Refer to Item 5-2 about automatic
⇔
manual switchover, and
setting method at the time of manual operation.
Choose
（
）
by key
、
Decide by
key, hen
Monitor LED’s RUN lights off and becomes control stop [Output
OFF (0%)] conducting.
Priority is given to DI when RUN is allotted to external control
input. DI Key operation cannot be performed unless allotment is
canceled.
When measuring range, a unit, scaling, and output characteristics
are changed it is initialized a
（
）
is displayed.
A manual output is canceled when an operation mode is made into
( ).
When a power source is intercepted and re-switched on, it returns
to the condition just before intercepting.
5-4. Explanation of each screen
(
1
)
Basic Screens
Basic Screen
Action Mode 1 screen
Basic Screen
3 seconds
(constant value control) lead screen of setting screens or (Program control) lead screen of setting screens
3 seconds
Press the key for 3 seconds on a basic screen, then it shifts to the lead screen of (constant value control) setting screens, or to the lead screen of (program
control) setting screens.
Press the key for 3 seconds on or the lead screen of setting screens, then it shifts to the basic screen. The shift is also possible when the program option is
added and is chosen on the operation mode 2 screen. The shift is possible when the program option is added and is chosen on the operation mode 2screen.
Basic Screens
Operation mode 1
key lock
PV offset correction
three seconds
Mode 1 lead screen
Mode 2 lead screen
Mode 5 lead screen
Mode 1
〜
5 screens
three seconds
Basic Screen
Output monitor
Automatic screen RUN lamp lights up
Output monitor
Manual screen RUN lamp blinks
Manual screen RUN lamp blinks
or
three seconds
Output monitor
《
Power-on
》
All LED light up
※1 Out 1 type
※2 Out 2 type
Basic screen
Input type
Upper limit & lower limit of measuring range
Output 1 monitoring screen
Executed SV initial value
：
Sensor input 0
Linear input Lower limit of scaring range
Setting range
：
Sensor input
Within measuring range
Linear input
With in scaring range
Within SV limiter besides
key
key
key
：
Contact
：
Voltage pulse
：
Current
：
Voltage
※2 Output 2 Displays only optional addition.
※1 ※2 This is the display when : contact
is choosen.
