background image

10

Guidelines & Recommendations 

for Extension Cords

When Using An Extension Cord, be sure to 

use one heavy enough to carry the current 

your product will draw. An undersized cord will 

cause a drop in line voltage resulting in loss of 

power and overheating. The table below shows 

the correct size to be used according to cord 

length and ampere rating. When In Doubt, Use 

A Heavier Cord. The smaller the gauge number, 

the heavier the cord.

Make sure your extension cord is Properly 

Wired And In Good Condition. Always replace a 

damaged extension cord or have it repaired by 

a qualified person before using it. Protect your 

extension cords from sharp objects, excessive 

heat and damp/wet areas.

Amperage

7.5 Metres

15 Metres

30 Metres

45 Metres

3.0A

18 Gauge

16 Gauge

16 Gauge

14 Gauge

Electrical Information

Guidelines for Using Extension 

Cords

If you are Using An Extension Cord outdoors, 

be sure it is marked with the suffix “W-A” to 

indicate that it is acceptable for outdoor use. 

Be sure your extension cord is Properly Wired 

and in good electrical condition. 

Always Replace A Damaged Extension Cord or 

have it repaired by a qualified person 

before using it.

Protect Your Extension Cords from sharp 

objects, excessive heat and damp or wet areas.

Summary of Contents for SBD-15























Reviews: