manualshive.com logo in svg

Sharper Image SI-755, Owner'S Manual

Share
Download
Sharper Image SI-755 Owner'S Manual Download Page 15

15

English

STORAGE & CARE

PROPER STORAGE

Preparing your Dual Voltage Travel Iron for storage is quick and simple. When you 

have finished your steaming tasks, follow the steps listed below.

IMPORTANT:

 Make sure Steam Button is locked in lowered position before storing.  

This will prevent any water from accidentally dripping.

1.

 

Unplug power cord from electrical outlet.

2. 

Prop unit upright on Stands.

 

Allow Iron Plate to cool (30 minutes for complete 

cooling).

3. 

Remove Water Tank Cap. Drain any water remaining in Tank into a sink or tub. 

Replace Water Tank Cap.

4. 

Wipe Main Body and Ironing Plate with a soft cloth lightly moistened with water.

-   

DO NOT

 clean Ironing Plate with detergents or descalers.

-   

DO NOT

 clean Ironing Plate with abrasive or corrosive products.

-   

DO NOT

 submerge unit or hold unit under running water.

5. 

Wrap power cord around unit and store in a cool, dry location.

MINERAL BUILD-UP

A common maintenance need for steam appliances is the removal of build-up 

caused by high mineral content in many municipal water supplies. This mineral 

build-up may cause the unit to spew water, limit the effectiveness and reduce the 

life of your Dual Voltage Travel Iron. 

Summary of Contents for SI-755




















Reviews:

No comments

Brands by name

Popular brands

Load more brands