E-5
General control
■
To turn the power on
Press the ON/STANDBY button to turn the power on or off.
■
Display brightness control
Press the DIMMER button (remote control).
Dimmer 1
Dimmer 2
Dimmer off
(Display is dim).
(Display is bright).
(Display gets dimmer).
■
Volume auto fade-in
If you turn off and on the main unit with the volume set to
27 or higher, the volume starts at 16 and fades in to the
last set level.
■
Volume control
Turn the volume knob toward /– (main unit) or
press VOL +/– (remote control) to increase or decrease
the volume.
■
Muting
To mute the volume, press the button (remote control).
Press again to restore the volume.
■
Direct key power on function
When you press any of the following buttons, the unit turns on.
●
CD
/
, USB
/
, AUDIO IN, TUNER, OPEN/CLOSE
(remote control): Selected function is activated.
●
/
(main unit): The unit turns on and playback of the
last function will start (CD, USB, AUDIO IN, TUNER)
■
Auto power off function
The main unit will enter the standby mode after approxi
-
mately 15 minutes of inactivity during:
Audio In: No detection of input signal.
CD: In the stop mode or no disc.
USB: In the stop mode or no media.
■
X-Bass control
When the power is first turned on, the unit is in the extra
bass mode. “X-BASS” indicator appears. To cancel this
mode, press the X-BASS button (remote control).
■
Bass or Treble control
1
Press the BASS or TREBLE button to select “Bass” or “Tre-
ble” respectively.
2
Within 5 seconds, press the VOL (+ or –) button to adjust the
bass or treble.
- 5
↔
- 4........
↔ +
4
↔ +
5
- 5
↔
- 4........
↔ +
4
↔ +
5
Press SOUND (DEFAULT) button to return sound to
default settings. “SOUND DEFAULT” appears on the
display.
Sound default settings : Bass = 0, Treble = 0, X-Bass = off
■
Function
Press the FUNCTION button repeatedly to select desired
function.
CD
FM MONO
FM STEREO
USB
AUDIO IN
Note:
The backup function will protect the memorised function
mode for a few hours should there be a power failure or
the AC power lead becomes disconnected.
Remote control
■
Battery installation
1
Open the battery cover.
2
Insert the batteries according to the terminal indicated in
the battery compartment. When inserting or removing the
batteries, push them toward the (–) battery terminals.
3
Close the cover.
Caution:
●
Replace all old batteries with new ones at the same
time.
●
Do not mix old and new batteries.
●
Remove the batteries if the unit will not be used for a
long period of time. This will prevent potential damage
due to battery leakage.
●
Do not use rechargeable batteries (nickel-cadmium
battery, etc.).
●
Installing the batteries incorrectly may cause the unit
to malfunction.
●
Batteries (battery pack or batteries installed) shall not
be exposed to excessive heat such as sunshine, fire
or the like.
Notes concerning use:
●
Replace the batteries if the operating distance is re-
duced or if the operation becomes erratic. Purchase
2 “AAA” size batteries (UM/SUM-4, R03, HP-16 or
similar).
●
Periodically clean the transmitter on the remote control
and the sensor on the unit with a soft cloth.
●
Exposing the sensor on the unit to strong light may in
-
terfere with operation. Change the lighting or the direc-
tion of the unit.
●
Keep the remote control away from moisture, heat,
shock, and vibrations.
■
Test of the remote control
The remote control can be used within the range shown below:
MICRO COMPONENT SYSTEM XL-LS701
Remote sensor
0.2 m - 6 m
(8” - 20’)
