4-10
VL-H870U
VL-H875U
VL-H890U
VL-H860S/H/VL-H870S
VL-H890S/VL-H94E
VL-H96E/VL-H960E
VL-H860S/H/VL-H870S
VL-H890S/VL-H94E
VL-H96E/VL-H960E
(3) Lower drum ass'y
Tighten the FPC mounting screw to the lower drum ass'y. The screw
tightening torque must be 0.08N·m (tighting torque 0.8kg·cm). (Fig-
ure 6)
(4) Upper drum ass’y
After fitting the gap shim which was removed when the upper drum
ass'y was dismantled to the shaft of lower drum ass’y, fit the upper
drum ass’y. (Figure 3)
At this time slightly turn the upper drum ass'y by hand to ascertain that
RTr does not scrape. If scrape is found, replace the gap shim with the
gap shim packaged together with the replacement upper drum ass’y.
(5) Drum motor stator
Fit the motor stator to the shaft. Then, apply the preliminary pressure
0.07N·m (0.7kg) to the motor stator, tighten the stator mounting
screw. The tightening torque must be 0.15N·m (1.5kg·cm).
Install the stator so that the chassis line is nearly parallel with the
motor stator straight section when it is installed on the chassis.
(Figure 9)
(6) Drum base
Align the positioning pin, and tighten the screws (3 pcs.).
(7) Drum ass’y
Install the drum ass’y on the main chassis, and tighten the screws (3
pcs.).
(8) Tape guide
Align the positioning pin, and tighten the screw (1 pc.).
Motor stator
Stator set
screw
Motor stator
circuit board
Arrange parallel.
FPC
Chassis line
Figure 9
4-5-5. Phase matching
The phase of the following parts must be matched as
shown in the figure below.
(Ascertain that the marks and round holes align.)
(1) Lo relay gear
(2) Main cam
(3) Sub-cam
(4) Mode switch
Lo relay gear
Phase
alignment mark
(Round hole)
Phase alignment
mark ( Mark)
Phase alignment mark
(Round hole)
Mode switch
4-6. MECHANISM ASSEMBLING METHOD
a
B
T arm guide
Segment gear
M-function lever
Move claw
to rear side.
Move claw to
rear side.
(1) Adjust the phase of each part.
(2) Install screws and washers.
(3) Install the segment gear, T arm guide and the M-function
lever. Install the eject lever.
Item
Tightening torque
Quantity
a S Tight M1.4 x 3
70mN·m (0.7kgf·cm)
1
B ø0.8-ø3-t0.2
1
Summary of Contents for VL-H860H
