Sharp UX-P110 Operation Manual Download Page 70 | Manualshive

Page: 70 / 84

background image

Maintenance

68

2

Flip up the green levers on each side of
the white roller.

3

Wipe the scanning glass (under the
white roller) and rollers with a cotton
swab.

•

Make sure that all dirt and stains (such
as correcting fluid) are removed. Dirt
and stains will cause vertical lines on
transmitted images and copies.

If the scanning glass is difficult to clean
If you find it difficult to remove dirt from the scanning glass, you can try moistening
the swab with isopropyl alcohol or denatured alcohol. Take care that no alcohol
gets on the rollers.

4

Flip down the green levers on each side of the white roller. Rotate the
front gear until the film is taut, and then close the operation panel (press
down on both sides to make sure it clicks into place).

The housing

Wipe the external parts and surface of the machine with a dry cloth.

Caution! Do not use benzene or thinner. These solvents may damage or
discolor the machine.

all.book

Page 68

Monday, August 19, 2002

4:05 PM

«
...
68
69
70
71
72
...
»

Summary of Contents for UX-P110





















































































Reviews:

No comments

Related manuals for UX-P110

Brand: ADJ Pages: 10

Brand: White Pages: 34

Brand: Kärcher Pages: 55

Dreamstitcher Portabl 787

Brand: Reliable Pages: 1

Snack Safety Point SVE SSP

Brand: SandenVendo Pages: 44

Brand: BRONDI Pages: 32

Brand: CIMLINE Pages: 52

Brand: CIMLINE Pages: 78

AMS-224EN6060/IP-420

Brand: JUKI Pages: 23

Brand: JUKI Pages: 2

Brand: Yamato Pages: 15

Hurricane Haze 3D

Brand: Chauvet Pages: 16

Brand: Yamato Pages: 42

Brand: Yamato Pages: 52

Brand: Yamata Pages: 34

FLEXIFOLD 1st STATION

Brand: Baumfolder Pages: 47

Brand: Standard Pages: 32

Brand: Radio Shack Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands