Sharp UX-P110 Operation Manual Download Page 27 | Manualshive

Page: 27 / 84

background image

Loading the Document

25

2. Sendi

ng

Fa

x

e

s

Other restrictions

♦

The scanner cannot recognise yellow, greenish yellow, or light blue ink.

♦

Ink, glue, and correcting fluid on documents must be dry before they pass
through the document feeder.

♦

All clips, staples, and pins must be removed from documents before loading
in the feeder. If these are not removed, they may damage the machine.

♦

Documents which are patched, taped, torn, smaller than the minimum size,
carbon backed, easily smudged, or have a slippery coated surface should
be photocopied, and the copy loaded in the feeder.

Loading the Document

One page can be placed in the feeder at a time.

♦

If you need to fax or copy more than one page, insert each additional page
gently and carefully in the feeder while the previous page is being scanned.
Do not try to force the additional page in, as this may cause double-feeding
or jamming.

1

Adjust the document guides to the
width of your document.

2

Insert the document face down in the
document feeder. The top edge of the
document should enter the feeder first.

•

READY TO SEND will appear in the
display.

all.book

Page 25

Monday, August 19, 2002

4:05 PM

«
...
25
26
27
28
29
...
»

Summary of Contents for UX-P110





















































































Reviews:

No comments

Related manuals for UX-P110

Brand: Singer Pages: 29

Brand: Advance acoustic Pages: 2

Brand: Pfaff Pages: 88

Brand: weasy Pages: 75

Brand: Gammill Pages: 26

Brand: Singer Pages: 108

Brand: Adler Pages: 5

Brand: Kärcher Pages: 12

Brand: PHC Pages: 4

Brand: Sase Pages: 76

Brand: Golden wheel Pages: 14

SQF-200 SquareFolder

Brand: Plockmatic Pages: 85

Brand: Kärcher Pages: 260

Brand: Pfaff Pages: 78

IP PHONEFAX 49A

Brand: Sagem Pages: 56

Brand: Advance acoustic Pages: 40

Brand: Consew Pages: 36

KM 70/30 C Bp Adv

Brand: Kärcher Pages: 147

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands