background image

7

STEP 10: LEVEL DISHWASHER

WARNING

 Dishwasher must be level for proper dish rack 

operation and wash performance.
•  Place level on door and rack track inside the tub as shown to check 

that the dishwasher is level.

Check Level

Front to Back

Check Level

Side to Side

•  Level  the  dishwasher  by  adjusting  the  four  leveling  legs 

individually.

Turn Legs 

to Adjust

TIP: Pull lower rack out, about halfway. Make sure the rack does 

not roll forward or back into dishwasher. If the rack rolls in either 

direction, the dishwasher must be leveled again.
•  If the door hits the tub, the dishwasher is not installed correctly. 

Adjust leveling legs to align door to tub.

INSTALLATION INSTRUCTIONS

STEP 8: SLIDE DISHWASHER PARTIALLY INTO 
CABINET

DO NOT PUSH AGAINST FRONT PANEL WITH KNEES. 

DAMAGE WILL OCCUR.
•  Slide dishwasher into the opening a few inches at a time.

•  As you proceed, pull the drain hose through the opening under the 

sink. Stop pushing when the dish washer is a few inches forward 

of adjacent cabinetry.

•  Make sure drain hose is not kinked under the dish washer and 

there is no interference with the water line, wiring or any other 

component.

STEP 9: POSITION DISHWASHER UNDER 
COUNTERTOP

•  Make sure that wires are secure under the dishwasher and not 

pinched or in contact with door springs or other dishwasher 

components.

TIP: Check tub insulation blanket, if equipped. It should be 

positioned so it is not bunched up or interfering with door springs. 

Check by opening and closing the door.
•  Push dishwasher into cabinet. The front corners of the dishwasher 

door should be flush with cabinet doors. Be careful not to dent 

front panel with knees or damage countertop or cabinets with 

dishwasher parts.

Summary of Contents for SDW6757ES













Reviews: