background image

6

INSTALLATION INSTRUCTIONS

STEP 4: INSTALL POWER CORD

Skip this step if dishwasher will be direct wired. Use power cord 

kit WX09X70910 available for purchase from an authorized Sharp 

parts dealer. The power cord and connections must comply with 

local codes and ordinances.
•  Recommended power cord length is 54" minimum and 64" 

maximum.

Green Wire to

Green Wire (Ground)

Black Wire to

Black Wire (Hot)

White Wire to

White Wire (Neutral)

Remove

Junction Box

Cover

•  Connect incoming power cords: white (or ribbed) to dishwasher 

white, black (or smooth) to black and ground to dishwasher green 

wire. Use cUL/UL listed wire nuts of appropriate size.

•  Replace junction box cover. Be sure wires are not pinched under 

the cover.

STEP 5: INSTALL 90˚ ELBOW

•  Wrap 90˚ elbow with thread seal tape. Do not use plumber's putty.
•  Install a 90˚ elbow onto the water valve.

•  Do not over tighten 90° elbow; water valve bracket could bend or 

water valve fitting could break.

•  Position the end of the elbow to face the bottom right of the 

dishwasher.

STEP 6: INSTALL DRAIN HOSE

•  Install the screw type hose clamps to the drain hose.
•  Connect the drain hose to the drain hose installation hose, then 

tighten the screw type hose.

The Drain Hose 

Installation Hole

STEP 7: INSERT DRAIN HOSE THROUGH CABINET

•  Upright the dishwasher and position in front of the opening. Insert 

drain hose into cabinet wall hole. If a power cord is used, guide 

the end through a separate hole.

Power Cord

(if used)

House

Wiring

Drain

Hose

Water

Line

Insulation

Blanket

Maximum

Drain Hose

Length 10'

TIP: Position water line and house wiring on the floor to avoid 

interference with base of dishwasher.

Summary of Contents for SDW6757ES













Reviews: