background image

5

R-390Aw
R-390AK

Pin

Pin

Upper oven hinge

Lower 
oven
hinge

Lower oven
hinge

Choke cover

Door assemby

Figure C-8. Door Replacement

DISPLAY UNIT LAMPS REMOVAL

Figure C-10. Back side view of display unit

LCD
vessel
tab

IC2

IC1

C11

LCD
vessel
tab

1. Disconnect oven from power supply and remove outer

case.

2. Discharge high voltage capacitor.
3. Remove the control panel assembly from the oven,

referring to "CONTROL PANEL ASSEMBLY REMOVAL".

4. Remove the five (5) screws holding the display unit and

the power unit to the control panel frame.

5. Remove the display unit and the power unit from the

control panel frame.

6. Remove the solder holding the tab (near capacitor C11)

of LCD vessel to the printed wiring board.

7. Make the four (4) tabs of LCD vessel straight.
8. Release the LCD vessel from the printed wiring board.
9. Now, the two (2) lamps LMP1 and LMP2 can be found.
10.Remove the solder holding the lamps LMP1 and LMP2

to the printed wiring board.

11.Now, the lamps LMP1 and LMP2 are free.

SEALER FILM

Installation
1. Put the adhesive tape on the backing film of the sealer

film as shown in Fig. C-9.

2. Tear the backing film by pulling the adhesive tape.
3. Put the pasted side of the sealer film on the door panel

Sealer film

Backing film

Adhesive tape

Figure C-9. Sealer film

Summary of Contents for R-390AK

















Reviews: