supplied accessories
If any component is missing, please contact your dealer.
□
HDBaseT Receiver Board: 1
□
Terminal label: 1
□
Operation manual (this manual)
□
Installation Manual (instructions for SHARP dealers and service
engineers): 1
• HDBaseT is a registered trademark of the HDBaseT Alliance.
• The terms HDMI and HDMI High-Definition Multimedia Interface, and
the HDMI Logo are trademarks or registered trademarks of HDMI
Licensing, LLC in the United States and other countries.
Connecting Peripheral Equipment
1
2
3
1. HDBaseT
terminal
Use a commercially available LAN cable (Category 6
or better shielded cable) to connect to an HDBaseT
transmitter.
2. usB
terminal
You can connect a USB mouse or keyboard (HID class)
to this terminal to control the computer connected to the
HDBaseT transmitter.
*
3. LaN
terminal
Use a commercially available LAN cable to connect to
the network. You can use this terminal in place of the
LAN terminal of the monitor.
Do not connect the LAN terminal to the same network
as the LAN that the board is connected to by way of
the HDBaseT terminal. A network loop malfunction will
occur.
* You have to use this product with a transmitter that supports the
HDBaseT 2.0 standard. Connections to all transmitters is not guaranteed.
About the HDBaseT Receiver Board
A commercially available HDBaseT transmitter is required to use
this board. Depending on the transmitter, some functions may not be
available. Check with the manufacturer regarding HDBaseT transmitter
specifications.
■ OPERATiNg THE mONiTOR
• When you use this device, set the input mode to OPTION.
• In some cases, the power of the HDBaseT receiver board may remain
on even in the standby mode or input signal waiting mode. Power
consumption will be higher when this occurs.
• The power consumption of the monitor with this board attached
increases by up to 12 W.
• To use LAN signals or RS-232C signals via HDBaseT and LAN signals
that have been applied to this board’s LAN terminal, change the
CONTROL ROUTE setting under COMMUNICATION SETTING on the
SETUP menu.
You can also use control commands to change the setting.
function
Command
Direction
Parameter
Reply
Control/
Responsecontents
CONTROL
ROUTE
CTCH
WR
0-1
0-1 0: MONITOR
1: OPTION
○
“○” indicates a command which cannot be used in standby mode when
POWER SAVE MODE is set to ON.
*
When CONTROL ROUTE is set to OPTION, the communication speed
is fixed to 9600 bps. Also, you cannot set POWER SAVE MODE to ON.
• AUTO INPUT SELECT PRIORITY is not supported.
• You can use the INFORMATION3 screen to check things such as the
communication status of the board as shown below. Set the input mode
to OPTION.
- SIGNAL STRENGTH: This displays the signal strength. The smaller
the value, the stronger the signal. To ensure stable operation, a signal
strength of at least -10 dB (-10 dB, -11 dB, -12 dB, etc.) is necessary.
- LINK STATUS: NO LINK, LINK, LOW POWER, or ETHERNET is
displayed. When LOW POWER is displayed, the link has been
established, but video cannot be transmitted. ETHERNET is displayed
when the cable that should be connected to the LAN terminal is
erroneously connected to the HDBaseT terminal.
- HDMI STATUS: NO HDMI, HDMI, or HDCP is displayed.
NO HDMI: No video data has been received.
HDMI:
HDMI/DVI data without HDCP is being received.
HDCP:
HDMI/DVI data with HDCP is being received.
*Set the input mode to OPTION before checking the status.
When you connect the HDBaseT Receiver Board, the following become
enabled on the monitor.
• If you are using an Extron device, set EXTRON XTP to ON under
COMMUNICATION SETTING on the SETUP menu.
• The following control commands become enabled.
function
Command
Direction
Parameter
Reply
Control/
Responsecontents
EXTRON
XTP
EXTN
WR
0-1
0-1 0: OFF 1: ON
○
“○” indicates a command which cannot be used in standby mode when
POWER SAVE MODE is set to ON.
■ PRODuCT SPECifiCATiONS
Model
PN-ZB03H
supported standard
HDBaseT 2.0
input/output terminals
HDBaseT terminal
LAN terminal (10BASE-T/100BASE-TX)
USB terminal (USB 2.0 compliant)
Max. resolution (pixels)
4096 x 2160 (30Hz)*
maximum transmission
distance
100 m*
copy protection
Supports HDCP (pass through)
Power requirement
Supplied from the monitor
input voltage
12 - 19 V
Power consumption
12 W
Dimensions
inch (mm)
Approx. 4-15/16(W) x 5-3/8(D) x
1-3/16(H) (124.6 x 136.5 x 30)
Weight
lbs. (g)
Approx. 0.408(185)
* To connect the devices, use a commercially available category 6 or
better shielded cable.
• Use this device within the operating temperature and humidity
conditions of the monitor.
As a part of our policy of continuous improvement, SHARP reserves the
right to make design and specification changes for product improvement
without prior notice. The performance specification figures indicated are
nominal values of production units. There may be some deviations from
these values in individual units.
Printed in China
16G CN1
