4
Locations that are excessively hot, cold, humid, or
dry (near heaters, humidifiers, air conditioners, etc.)
The paper will become damp and condensation may form
inside the machine, causing misfeeds and dirty output.
If the location has an ultrasonic humidifier, use pure
water for humidifiers in the humidifier. If tap water is
used, minerals and other impurities will be emitted,
causing impurities to collect on the inside of the
machine and create dirty output.
When the machine is installed, the adjusters must
be lowered to the floor to secure the machine
(prevent it from moving).
Rotate the adjusters in the locking direction until they
are in firm contact with the floor.
If you find it necessary to reposition the machine
due to rearrangement of your office layout or
other reason, retract the adjusters from the floor,
turn off the power, and then move the machine.
(After moving the machine, lower the adjusters again
to secure the machine.)
Locations exposed to direct sunlight
Plastic parts may become deformed and dirty output
may result.
Locations with ammonia gas
Installing the machine next to a diazo copy machine
may cause dirty output.
Do not install the machine in a location with poor air
circulation.
A small amount of ozone is created inside the
machine during printing. The amount of ozone created
is not sufficient to be harmful; however, an unpleasant
odor may be noticed during large copy runs, and thus
the machine should be installed in a room with a
ventilation fan or windows that provide sufficient air
circulation. (The odor may occasionally cause
headaches.)
* Install the machine so that people are not directly
exposed to exhaust from the machine. If installed near
a window, ensure that the machine not be exposed to
direct sunlight.
Near a wall
Be sure to allow the
required space around
the machine for servicing
and proper ventilation.
(The machine should be
no closer than the
distances indicated below from walls.)
Locations subject to vibration.
Vibration may cause failure.
The machine includes a built-in hard drive. Do not
subject the machine to shock or vibration. In particular,
never move the machine while the power is on.
• The machine should be installed near an accessible
power outlet for easy connection.
• Connect the machine to a power outlet which is not
used for other electric appliances. If a lighting fixture
is connected to the same outlet, the light may flicker.
Machine
30cm
15cm
30cm
About consumables
CAUTION
Do not throw a toner cartridge into a fire.
Toner may fly and cause burns.
Store a toner cartridge out of the reach of children.
Handling precautions
WARNING
Do not place a container of water or other liquid, or a
metal object that might fall inside, on the machine.
If the liquid spills or the object falls into the machine,
fire or electrical shock may result.
Do not remove the machine casing.
High-voltage parts inside the machine may cause
electrical shock.
Do not make any modifications to this machine.
Doing so may result in personal injury or damage to
the machine.
Do not use a flammable spray to clean the
machine.
If gas from the spray comes in contact with hot
electrical components or the fusing unit inside the
machine, fire or electrical shock may result.
If you notice smoke, a strange odor, or other
abnormality, do not use the machine.
If used in this condition, fire or electrical shock may result.
Immediately switch off the main power and remove
the power plug from the power outlet.
Contact your dealer or nearest SHARP Service Department.
If a thunder storm begins, switch off the main power
and remove the power plug from the outlet to prevent
electrical shock and fire due to lightning.
If a piece of metal or water enters the machine,
switch off the main power and remove the power
plug from the power outlet.
Contact your dealer or nearest SHARP Service
Department. Using the machine in this condition may
result in electrical shock or fire.
CAUTION
Do not look directly at the light source.
Doing so may damage your eyes.
Do not block the ventilation ports on the machine.
Do not install the machine in a location that will
block the ventilation ports.
Blocking the ventilation ports will cause heat to build
up in the machine, creating a risk of fire.
!mxm6070_us_sg.book 4 ページ ２０１８年３月５日 月曜日 午後４時５２分
