Sharp MX-C301, Quick Start Manual

Page: 4 / 20

4
Caution!
For complete electrical disconnection, pull out the main plug.
The socket-outlet shall be installed near the equipment and shall be easily
accessible.
Shielded interface cables must be used with this equipment to maintain
compliance with EMC regulations.
The equipment should be installed near an accessible socket outlet for
easy disconnection.
Each instruction also covers the optional units used with these products.
For the users of the fax function
(for MX-C301W)
(Note)
Use modular cable of 10m or less length to connect an external
telephone.
Important safety instructions
• If any of your telephone equipment is not operating properly, you should
immediately remove it from your telephone line, as it may cause harm to the
telephone network.
• Never install telephone wiring during a lightning storm.
• Never install telephone socket in wet locations unless the socket is
specifically designed for wet locations.
• Never touch uninsulated telephone wires or terminals unless the telephone
line has been disconnected at the network interface.
• Use caution when installing or modifying telephone lines.
• Avoid using a telephone (other than a cordless type) during an electrical storm.
There may be a remote risk of electric shock from lightning.
• Do not use a telephone to report a gas leak in the vicinity of the leak.
• Do not install or use the machine near water, or when you are wet. Take care
not to spill any liquids on the machine.
• Save these instructions.
Important Notice for New Zealand Users
General
“The grant of a Telepermit for any item of terminal equipment
indicates only that Telecom has accepted that the item complies
with minimum conditions for connection to its network. It indicates no
endorsement of the product by Telecom, nor does it provide any sort
of warranty. Above all, it provides no assurance that any item will work
correctly in all respects with another item of Telepermitted equipment
of a different make or model, nor does it imply that any product is
compatible with all of Telecom’s network services.”
This equipment is not capable, under all operating conditions, of
correct operation at the higher speeds for which it is designed.
Telecom will accept no responsibility should difficulties arise in these
circumstances. This condition typically applies to 56 kbit/s modems.
This equipment shall not be set up to make automatic calls to
Telecom’s 111 Emergency Service.
This equipment should not be used under any circumstances that
may constitute a nuisance to other Telecom customers.
This equipment may not provide for the effective hand-over of a call
to another device connected to the same line.
In order to operate within the limits for compliance with Telecom’s
specifications, the associated equipment shall be set to ensure that automatic
calls to different numbers are spaced such that there is not less than 5
seconds between the end of one call attempt and the beginning of another.
Notice for Users in Australia and New Zealand
Your fax machine and the telephone system
WARNING NOTICE:
NO calls can be made to or from this fax during a mains power failure.
WARNING
Australian Communications and Media Authority (ACMA) regulations
state that no unauthorised changes or modifications to this equipment
are permitted.
Complies with the following standards,
AS/NZS 60950.1
AS/CA S002, NZ TELECOM and AS/NZS CISPR 22
Software licence
The SOFTWARE LICENCE will appear when you install the software from the CD-
ROM. By using all or any portion of the software on the CD-ROM or in the machine,
you are agreeing to be bound by the terms of the SOFTWARE LICENCE.
• The explanations in this manual assume that you have a working knowledge
of your Windows or Macintosh computer.
• For information on your operating system, please refer to your operating
system manual or the online Help function.
• The explanations of screens and procedures in this manual are primarily for
Windows 7 in Windows
®
environments. The screens may vary depending on
the version of the operating system.
• This manual contains references to the fax function. However, please note that the
fax function is not available in some countries and regions.
• This manual contains explanations of the PC-Fax driver and PPD driver. However,
please note that the PC-Fax driver and PPD driver are not available and do not
appear on the software for installation in some countries and regions.
In this case, please install the English version if you want to use these drivers.
• Considerable care has been taken in preparing this manual. If you have any
comments or concerns about the manual, please contact your dealer or
nearest authorised service representative.
• This product has undergone strict quality control and inspection procedures. In the
unlikely event that a defect or other problem is discovered, please contact your dealer or
nearest authorised service representative.
• Aside from instances provided for by law, SHARP is not responsible for failures
occurring during the use of the product or its options, or failures due to incorrect
operation of the product and its options, or other failures, or for any damage that
occurs due to use of the product.
Wireless LAN (for MX-C301W)
The communication range of wireless LAN may shorten or
communication may not be possible in some usage environments,
due to shielding materials, the installation location, the effects of
ambient radio noise, data transmission speed, and other factors.
Warranty
While every effort has been made to make this document as accurate and
helpful as possible, SHARP Corporation makes no warranty of any kind with
regard to its content. All information included herein is subject to change
without notice. SHARP is not responsible for any loss or damages, direct or
indirect, arising from or related to the use of this operation manual.
© Copyright SHARP Corporation 2014. All rights reserved.
Reproduction, adaptation or translation without prior written
permission is prohibited, except as allowed under copyright laws.
Safety data sheet
The SDS (Safety Data Sheet) can be viewed at the following URL
address:
http://www.sharp-world.com/corporate/eco/env-info/sds/index.html
This product is designed for commercial application only and
as such it falls outside the scope of Regulation (EC) 1275/2008
implementing EU Directive 2005/32/EC on eco-design requirements
for standby and off mode electric power consumption. Sharp does
not recommend the product for domestic application and will not
accept any liability for such use.
Wave length 790 nm ± 10 nm
Pulse times (9.97 µs ± 0.034 µs) / 7 mm
Output power Max 0.6 mW (LD1 + LD2)
Caution
Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
This Digital Equipment is CLASS 1 LASER PRODUCT (IEC 60825-1 Edition 2-2007).
Laser information
These limits are designed to provide reasonable protection against
interference in an installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause interference. However, there
is no guarantee that interference will not occur in a particular installation.
If this equipment does cause interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a different circuit to that
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The Ringer Equivalence Number (REN) for this equipment is written
on the label.
Important safety information
In Australia, installing or modifying telephone lines should only be
done by an ACMA licenced serviceman. In New Zealand, installing
or modifying telephone lines should be done in accordance with
Telecom wiring practices.