manualshive.com logo in svg

Sharp JH-3500U, Installation & Operator'S Manual, Page: 22 / 33

Share
Download
Sharp JH-3500U Installation & Operator'S Manual Download Page 22

19

Installing Solar Power Conditioner Display

Follow all WARNING and CAUTION 

on

 Location o

f

 Installation Instructions (page 6).

WARNING

• Do not install the display outdoors, as it may 

be damaged leading to 

smoking or fire.

CAUTION

• Signal cable of the display should not be cut or fastened, as it may cause malfunction.
• Use the included signal cable to connect the solar power conditioner and the display.
• Do not pull the signal cable at the connector, as it may 

break the wire

.

1. Insert the larger 4-pin connector of the signal cable to the display jack in the solar power

conditioner 

(listen for 

clicking sound

 that ensures it is locked in place

).

2. Connect the ground cable to the ground terminal in the solar power conditioner,

and tighten the installed screw 

with 

Phillips screw driver.

3. Insert the flat-head screwdriver into the slits on the bottom of the display, and 

twist 

the screw

driver 

in

 the direction of the 

diagram to open the front cover

(See below for detail).

4. When the front cover is 

opened 

(

small

 clicking sound), remove the front cover.

5. Insert the smaller connector of the signal cable from the backside of the display.

Summary of Contents for JH-3500U


































Reviews:

No comments